CRT182HNB0 Crosley Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from Pilesgrove, NJ
- Parts Used:
- 240360801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lost the temperature control know
The knob came in the plastic package. It was the correct part. I opened the package and placed the knob on the prongs. Now it works fine.
Thanks
John S.
Thanks
John S.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from MELBOURNE BCH, FL
- Parts Used:
- 218428101
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Handle broke off of door
New handle was easy to obtain from you and had the new one on in ten minutes. Thank you Very easy repaired.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from FORESTDALE, MA
- Parts Used:
- 241872513
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door gasket torn on top
followed installation video on your website which was very helpful. Very easy repair. The packing material was great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nathan from WELLS, ME
- Parts Used:
- 5303918202
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Refrigerator and freezer running to warm.
I watched the video on how to change the defrost thermostat. I removed the back cover inside the freezer then I pulled off the old defrost thermostat and then using a pair of wire cutters I cut it off and then bared a little of both of the wires and then slid the heat sherink and wire connectors on the existing wires and then slid the other ends of the wires into the wire connectors then crimped the ends of the connectors and then tried using heat on the heat shrinks but still used rubber electric tape over it. I clipped the new thermostat were the old one was and then reattached the freezer wall cover and plugged the refrigerator back in. 24 hours later I checked the temperature in the refrigerator and freezer and both are running a lot colder.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leondra from RICHMOND, VA
- Parts Used:
- 240534901
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door Shelf Retainer Bar need to be replaced
1. Remove from box. 2. Snap into place. (30 sec.) + part arrive 2 days ahead of ETA (Ground Ship)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from CARIBOU, ME
- Parts Used:
- 240534701
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
retainer bar broke
took the old one off and snapped the new one in place. Very easy to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from SABINSVILLE, PA
- Parts Used:
- 5303918202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
freezer cold and frosting up but refrigerator warm
inside the freezer compartment, remove four hex head screws from rear panel,lift panel forward and unplug wire assembly from panel. find old defrost thermostat attached to copper tube by clip on back of thermostat, unclip, snip two wires to thermostat, take new thermostat, strip 1/4"of wire from wires in freezer (thermostat is prestripped),insert light blue wire from thermostat and light blue wire from freezer into opposite ends of crimp connector and crimp securely. repeat with dark blue wires. set panel back in freezer,connect plug to back of panel, refasten screws and you are go to go! save yourself the price of a new refrigerator or $300 repair by repairman!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from Newberry, SC
- Parts Used:
- 5303918202
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
the freezer frosted up and the fridge was not getting cold.
I watched the instructional video and did what it said.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from LOS ANGELES, CA
- Parts Used:
- 218428101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Someone broke ref. Door handle in garage, with car door!!!!
Just screw new one on again. All done, like new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnnie from NEWPORT, TN
- Parts Used:
- 241872512
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Gasket broke on bottom
Popped the old one out and pressed the new one in. Very easy. Pressed new one in my hands. Fits in a channel. Very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosemarie from BOYNTON BEACH, FL
- Parts Used:
- 218428101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Door Handle Broke off
Part arrived in tack.
Removed original screws. Place bottom of handle on sideways then horizontal position.
Next slightly raised top of handle over bump protector. Took orginial screw and screwd Top of door handle into place. Really easy!
Removed original screws. Place bottom of handle on sideways then horizontal position.
Next slightly raised top of handle over bump protector. Took orginial screw and screwd Top of door handle into place. Really easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from SAN MATEO, CA
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Repaired Oven Range Light Bulb
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Andover, CT
- Parts Used:
- 5304507147
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Refrigerator door was not sealing correctly.
Remove screws from lower hinge and carefully remove the door. In my case it was the lower bearing, flip door upside down being careful to remove anything which might fall off first. I removed the door stop and then pulled the broken bearing out with pliers. Then I pushed the new one in and reassembled it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from ONTARIO, CA
- Parts Used:
- 241839407
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Only one way on my fridge the two ovals snap into place
Just pushed the grill on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from N KINGSTOWN, RI
- Parts Used:
- 5303918202
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Freezer was not defrosting
Turned off fridge circuit breaker
Removed all food from freezer and put in cooler.
Removed shelves from freezer
Removed ice maker
Removed 2 hex head screws
Tilted back evaporator cover and tried to unplug connection.
Found connection was iced over with a huge block of ice coming from water inlet to ice maker
Spent several hours trying to melt and chip away ice without damaging fridge.
Finally was able to break up ice with long flat head screwdriver and hammer.
Unplugged connector and was able to remove evaporator cover.
Cut wires near thermostat and removed
Stripped wire as needed and crimped new thermostat in place.
Used heat gun and lighter to melt heat shrink. This took a long time and required a lot more heat than expected.
Reconnected evaporator cover connection and reattached cover.
Reinstalled ice maker
Reinstalled shelves.
Put food back in
Turned circuit breaker back on.
Removed all food from freezer and put in cooler.
Removed shelves from freezer
Removed ice maker
Removed 2 hex head screws
Tilted back evaporator cover and tried to unplug connection.
Found connection was iced over with a huge block of ice coming from water inlet to ice maker
Spent several hours trying to melt and chip away ice without damaging fridge.
Finally was able to break up ice with long flat head screwdriver and hammer.
Unplugged connector and was able to remove evaporator cover.
Cut wires near thermostat and removed
Stripped wire as needed and crimped new thermostat in place.
Used heat gun and lighter to melt heat shrink. This took a long time and required a lot more heat than expected.
Reconnected evaporator cover connection and reattached cover.
Reinstalled ice maker
Reinstalled shelves.
Put food back in
Turned circuit breaker back on.
Was this instruction helpful to you?
Thank you for voting!