CRT206QW7A Crosley Refrigerator - Instructions

I simply snapped the proper pieces in place. It was sooo easy!

snap and done

There were no screws to remove or add. All were snap on parts.

It was so easy! I just slipped the shelving units in to the groove of the refrigerator, and it took approximately 2 minutes. I am so glad that I came across this company, because for the last 3 years I have tried to fix the shelving.

First I removed the top screws, then I slide it off the lower screw that is hidden behind the handle. I replaced the handle by sliding it onto the bottem first then attaching it onto the top with the two top screws.

I unplugged the refrigerator, then opened the door and removed four screws holding the plastic electrical panel to the interior top of the main refrigerator compartment and noticed the cold control was corroded badly, apparently from moisture in the panel. I ordered a new one from partselect.com. When it arrived the next day, I then pulled off the control knob, unclipped the cold control, unplugged the three wires to the control, then removed the styrofoam insulation blocks holding the thermocouple wire and then removed the thermocouple wire to complete the removal. I then reversed the process to install the new thermostat and control. That is repositioned the thermocouple wire, put the insulation blocks back to hold the wire, then replugged the three electrical wires, clipped the control back and pushed the control knob back on and finally screwed the panel back to the top of the main compartment and plugged the refrigerator electrical cord back in to provide current to the refrigerator. It immediately started up and ran fine. Total time - about 8 minutes.

I simply snapped in the new part. It took a few seconds. I would like to say that I found the part using the model number of the fridge. When I went to look at the description it said the part was 26 inches. The one I had was only 24 3/4 inches. I called you guys and was told that this was the correct part and to ignore the measuement.
You were Right! the part fitted perfectly.

This repair was very easy and took less than five minutes. I used the same screws that were on the fridge to put the handle in place. All I needed was a screwdriver. I would also like to add that when I ordered this part it was shipped the same exact day and I received it the next day. It was incredibly fast and I will use them again in the future. I recommend this company to those who need to replace or repair a part. Thanks PartSelect!

Unscrewed the old screws and removed broken piece of handle. Put new screws in for handle to latch in. Swung handle in place and put the 2 special screws in top of handle. Job done. With the correct parts from Parts Select The replacement was a breeze. Thanks for your speedy delivery and support. I will definitely continue to get all my various appliance parts from you

Respectfully

Roy

Remove the broken piece by tilting upward and then sliding straight out.
Simply replace with the new door shelf by aligning the small hooks with the slots on the door. Tilt the shelf up, insert the hooks into the slots and then tilt the shelf back down to its normal postion. It is now locked in place and you are done!

Frig area was at about 50 degrees and would not get cooler. Freezer was working great.
Empty the freezer and remove the two screws that hold the back panel of the inside of the freezer on. Pull the panel out and you will see the fan that is mounted to the back of the panel. If the fan is not running, disconnect it (quick connector) and check to see if there is voltage coming to it from the connector (should be 120VAC between the two wires). If there is power, and the fan was not working, replace the fan.

Fan just snaps into the holder on the back panel and plugs into the quick connector. Make sure you clear any ice build-up in the hole between the freezer and the frig that the fans blows through. Put it back together and verify the fan runs.

- Unsnapped old light socket from top of Frig
- Disconnected elect wires
- Reconnected elect wires to new light socket
- Snapped new socket in place
- Done in less than 2 min.

first i removed the four screws that hold the shelve in place disconnected the wire replace both diffuser-air,reconnected the wire and replaced the screws

just snap the new piece in place.

I slid the new glass in place