CT17X4W (DC33A) Crosley Refrigerator - Instructions

Followed the other directions -- I have the bottom tray freezer. It was really easy to unscrew the screws -- a bit of a reach to get them all, but not a problem. Leave the top screws half-way in and it's a bit easier (the icemaker has the brackets that just sit on the screws). Thanks to everyone who left instructions!

I took the screws out holding old old ice maker, unpluged the electrical socket and old unit came right out. All I had to do then was plug electrical socket into new icemaker place unit in position and put the one screw back in the held it in place. Plug frig and and it filled with water in about 15 minutes and started making ice. Part was a exact match to the one I removed.

Piece of cake. Removed two screws, pivoted old ice make up, lifted it out of the mounts. Installing the new one was just the reverse.

Identifying the correct replacement ice make was easy also, due to the photographs on PartsSelect.com

There was three screws to remove to unmout the ice maker, and unplug the wire harness,then two to remove to slip in new stripper. All took about 20 mins.

I removed the old icemaker, took it out to my shop & removed the wiring and etc. and put it back in place.

First I removed the screw holding the ice maker on the wall and then loosen two other screws in oreder to remove the maker. Once out, I replaced the maker with the new one. Then replaced it in the refrig.

Unplug fridge, close off water supply valve. Remove two screws attaching assembly to freezer wall, detach wiring harness. Remove parts from old assembly: wiring harness, shut-off rod, harness clamp and attach to new assembly. Connect wiring harness, two screws attach new assembly to freezer wall. Plug in fridge and open water supply valve (after an opportunity to change in-line filter). Works now!

Ordered new part by the numbers and pics. and installation was so easy. I thank you very much

used 1/4 inch wrench to remove bottom screw
and loosend tip screw and removed valve wires and water line

Most of the stories on repairing this ice maker indicated that was real easy until describing the Amana version. The fill tube attaches differently. The recommendation was to use your old "cup". I have found that to make the change required that you find a philips screw driver and locate two access holes in the motor end of the control unit. you can loosen those two screws (they won't fall out) all of the way and pull the control unit from the tray part of the ice maker. DON'T remove the three screws that hold the control unit together or rotate the sprocket. This will allow you to disassemble the parts that hold the "cup" in place. Just remember "if it isn't coming apart easily your not doing it right".

I simply removed 3 nut head screews and the old unit came off. I removed the ice level arm off the old unit and put on the new one. I removed the old wire harness and plugged into the new unit. I mounted the new unit, plugged it in and was done. I had ice in less than an hour. So simple my 11 year old could have done it without help.

First I loosened 2 phillips head screws at the top of the ice maker (the one that is close to the front is a little difficult to get a screwdriver on). These 2 screws do not have to be removed. Took 1 screw out of the L-bracket at the bottom of the ice maker. I then slipped the icemaker upward from the 2 top screws and unplugged the electrical wires at the connector at back of the refrigerator to remove the ice maker. I then removed the front cover from it and placed it on the replacement ice maker. I also swapped the L-brackets on the two ice makers as the new one was bent. I then reinstalled the new Ice maker in the reverse order.

The swap was quite easy. All I had to do was remove 3 nuts and unplug the flat wire connector. I kept the old unit when I took it out in case I needed any parts, but the only thing I needed to transfer over was the Ice level wire. Very straightforward!

I pulled the old one out and went on-line to find a part. Once I found the right sight that had the part I ordered it and had it shipped to my house. When the part came in just a few days I installed it and now it's working just fine......

Initially I turned off the power to the unit ( I found no need to disconnect water source. I believe it is controlled by the unit and is in the "off" position when powered down) then I loosened the top two screws, removed the bottom screw and slid the unit off of the upper mounting screws. Taking a flat screw driver blade I pushed down on the connector's locking nib within the maker and released the connector. I then reversed the procedure to reinstall making certain that the connector was fully pushed in. Tightened things down, turned on the power and had 'cubes" in about 1 hour. Easy fix, "repair" stories on site make this incredabily simple.