WRS26MR4JB4 Crosley Refrigerator - Instructions

Removed 4 screws holding face plate onto ice bucket. Removed the 3 screws holding the ice crusher housing. Noted postion and rotation of teh s;ring loaded ice selecting rod. Removed broken crusher housing. Reveresed process for installion. Took for test drive. Operational...

The repair was easy. The problem was the lack of explanation. This may help other customers. I was told by the virtual trouble shooting system that about 30% of the cure was to replace the water filter and 70% was to replace the water valve. I did both and still had the problem. People need to be told why they have to replace the water valve. The reason is this. The valve has a very small leak in it that lets water continue to flow into the freezer compartment drop by drop. Eventually, this freezes and clogs the hole , so no water can pass and thus no ice can be made.In either your web site or another they stated that it may freeze up here, but there was no connection to the water valve.It seemed like it was another topic. Its very hard to see the frozen area, unless you remove it from the freezer area. I wish I was TOLD TO DO THIS, after i replaced the valve It would have saved me a repair bill. I hope this helps others.
Take care-Bill

Pulled the old ice container assembly out and discarded it and inserted the new one. It immediately worked and now dispenses both crushed and cubed ice through the door.

Installed 3 new door shelves, took less in then 10 minutes. Yes, all 3 broke at once. The original shelves were cheap. The new ones from Parts Select feel a lot more durable.

The radiator was not being properly defrosted and the refrigerator and freezer could not keep the temperature. Two things can be causing this, the defrost module which defrost the refrigerator on a regular basis ($110) or the thermostat ($18). I tried the thermostat since it is very easy to do (remove cover plate inside the freezer, cut wires of old thermostat, connect new thermostat by stripping wires. Presto...however the thermostat was NOT the problem. The problem was a blown timer circuit board that controls the regular defrosting. That repair was done by a technician. The board was $110, it seats inside the refrigerator in the control panel area.

I followed a gentleman's directions on your website, very useful I might add. It helped me replace all the broken parts with ease. I am a 33 year old mom of two. Anyone could do these repairs that I did. Thank you.

This process was so easy. I put in the model # and saw the piece I needed immediately along with a picture of it that helped me confirm it was the right one. All I had to do is snap the shelf in when it arrived.

It takes a 1/4 " nutdriver to take one screw out that holds the cover over the water filter. You have to come up from the botton of cover. Then take two water lines off housing , by pushing the round collar back toward the fitting,and pull fitting off housing. Then take the two screw out that hold the housing on. Make sure you have the water turned off before you start.

Unplug turn water off
Removed two screws with nut driver loosen one
Disconnected three solenoid valves
Disconnected four water lines
Plug tubing in, tighten one flare fitting
Reattach wires to solenoids
Slide under loose screw, replace two screws
Turn water on check for leaks plug in get a drink of water

Loosen two screws, unclip electrical connection, remove ice maker, remove l shaped leveling piece of metal from old one, put on new one. Install in reverse order. Hint.. when loosening two screws, use a mirror

Remove both crisper pans and covers. Discard old frames and re-use glasses. Use two screw drivers to gently pry out broken supports. Top broken off smooth on one support. Unable to grasp with pliers to pull out. I drilled a small hole in the center of the large expansion pin. I screwed in a small sheet metal screw. Used side cutter pliers to grasp screw and gently rock back and forth to remove center of large pin. Plucked out broken pieces with needle nosed pliers. Gently tap in expansion pins to install new supports. The rest is simple re-assembly using new parts. "Nothing to it but to do it."

Just snapped into place. Very easy.

The door has nylon gear teeth that wore out and needed replaced. The ice chute came off very easy with 6 screws. I used a punch and pliers to remove the hinge pin. Then the door came off and the new one put on. Very easy. The part was ordered on Sunday and arrived on Tuesday.

Test the light socket first with a bulb that you know is good. If the light still does not come on, unplug the refrigerator, remove the switch by inserting a very small, thin, flathead screwdriver alongside it and pull the switch out slowly with your other hand. There are two wires there. Remove them gently with some needle nose pliers. If you want to test to see if the switch is defective, take a insulated jumper wire, and attach it between the two wires. Plug the refrigerator back in and see if the light comes on. If the light does come on, replace with a new switch by re-attaching the wires and placing it back in the hole firmly.

old gasket is very easy to pull off. putting the new gasket will only took me few minutes to put on, just make sure you press it firmly .everything works out right .