WWSS2601KW0 Crosley Refrigerator - Instructions

- Unsnapped old light socket from top of Frig
- Disconnected elect wires
- Reconnected elect wires to new light socket
- Snapped new socket in place
- Done in less than 2 min.

Partselect made it easy and affordable to replace the part myself. It arrived on the 3rd day after ordering. Thanks

Most of the time was spent removing frozen food and removing the plastic clip holding one of the shelves in place. Removal of bottom panel took less than a minute. Thermostat easy to find, clipped wires a the unit and removed unit. Used included wire jackets, but not white shrink wrap. This did NOT fix the problem. This was the attempt at a 'cheap' fix. My refrigerator required the 'control box' to be replaced.

1.Got on line to Partselect ordered the parts we needed .they arrived Quickly and in good condition 2.Except the tray was sent in error delaying the repair. 3.contacted Partselect costumer services for assistance 4.Followed their direction and reorder the correct one hoping the correct one would arrive .it did the next day .5.On to repair, removed broken stud with panel stud puller with the aide of a putty knife to spread the pressure of tool stud came out 6.reinserted new stud 7.replaced the new upper crisper drawer cover glass not included . 8.Upper Crisper pan to complete the repair. 9.all in all successful with the help of Partselect superior parts and helpful guides.

Replacement of bins were simple the crisper cover supports were a little more time consuming since the manufactured piece were glued in. I used a tool that has a 30% tip and hooked the support and pulled in out part of the way and pulled the rest out with my fingers. All in all a simple job...I took the opportunity to do an addition cleaning of the inside of fridge with my extra time. Would also like to say that my parts were delivered within 24 hours of ordering them and the website made purchasing easy and no second guessing, since the model had an exploded version of all the parts available. Thank you

Simply slid glass into frame & it fit perfectly.

The shelving brackets are install much like a blind rivet. I simply used a punch and gently pushed in the plastic center pin / mandrel. I then used a butter knife as a wedge to pull out the shelving supports enough to grab them with a pair of pliers. Simple to do!

Bought a new
capacitor.

The 4 lines attached to water valve have compression fittings.New valve has pex fittings.I cut each line just behind the ferrel and inserted each line into the proper fitting and reattached the 3 electrical plugs.Turned water back on.I immediately got water from thr door without dripping.For whatever reason it was not making ice for the first 3 days,I pulled the plug on the icemaker solenoid and reattached.It is working now.

It was fairly easy. Only had to remove the back cardboard. Remove 3 screws and the power plug.
Replacing the screws took a little time the motor mount didn't seem to be tapped exactly for the screws supplied and it was in a tight area. Its working great now.

First of all Don't panic! you can do it and you can save a lot of $$$ if you do it yourself. A friend advice me to look it up online resources and came accross part select on YouTube .

The process:
Defrost the fridge. Take down the panels on the fridge to have room to unscrew the back panels. Once you've taken the back panel out. You will see the thermostat right away. Replace it and voila you're done.

Pull refrigerator away from wall, being careful not to kink or break water line to ice maker, unplug refrigerator. Using 1/4" nutdriver, remove cardboard lower rear panel, bottom lifts out. Fan and motor are now directly in front of you, grasp the moter to stablize it, and using your other hand, pull fan hub from motor shaft. Be sure motor shaft is clean before reinstalling new fan blade, press new bladr onto motor shaft, until center of blade is centered on outlet side of fan housing. spin blade by hand to insure clearance. Plug refrigerator in and observe operation of fan, refrigerator needs to be calling for cooling for this fan to operate. Reinstall cardboard panel and move refrigerator back into position.

Replaced the plastic/nylon piece on the door. First, I remove the door hinge cover by unscrewing the one bolt. Second, unbolted the two bolts that hold the door in place. Third, lifted the door off the bottom hinge. Four, remove the bottom plate that is held in place by 3 screws. Five, using pliers move the old plastic piece from the bottom of the door. Six, press into place the replacement part. Seven, re-install the bottom plate. Eight, rehang the door on the bottom hinge. Nine, restall the top hinge and rebolt the two bolts that hold the hinge in place. Ten, reinstall the top cover. Finished.

Followed the steps in the video on your site, really easy to do.

Removed the two screws that hold the element in place. Then I pulled the element out about 3 inches and disconnected the wires. Everything matched up perfectly.