CRTE217IAQ2 Crosley Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jeff from Lakeville, MN
- Parts Used:
- 240505801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light switch did not operate correctly
Piece of cake! The new part just plugged in to socket and back into fridge frame. Appreciated how easy it was to order this part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leon from Upper Marlboro, MD
- Parts Used:
- 240338001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Shelf Held Together with Rubber Bands
Old shelf was removed and the new shelf clicked right into place, an exact match, perfect fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Lancaster, CA
- Parts Used:
- 240313703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
The original part was plastic/and broke
unscrewed to little bolts and installed the new/metal part we got rfom partselect.If we may say.this is a great company to buy from! Fast!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lori from Catskill, NY
- Parts Used:
- 240338101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The door shelf broke.
Very easily did the repair -- popped the new door shelf right in the place of the old one! No tools needed, no hardware, easy! The part actually measured 24 3/4 but the replacement part said "26 inches" on website & this was THE replacement part. Put this off for so long--ordered part and recd within 2 days, great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allan from North Miami, FL
- Parts Used:
- 240338001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken door shelf bin
Opened the box, snapped it in place. Took longer to just open the box! I carefully inspected the part and compared to the original. I could not tell them apart. The fit and finish is perfect. This is a very well made product. Easy to order, fast shipping, well packaged and very easy to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janice M. from Washington, DC
- Parts Used:
- 240505801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door Would Not Close
I stuck a small screw driver under the old switch & it came out really easy. I just unplugged the 2 electrical connectors, and removed the old switch. Installing the new one was just as easy. I am a woman!
I also want to say how FAST PartSelect gets their items to you. It came in ONE day!
Your repair stories are very helpful, I/we would have never known how easy this switch was to replace! Thank you!
I also want to say how FAST PartSelect gets their items to you. It came in ONE day!
Your repair stories are very helpful, I/we would have never known how easy this switch was to replace! Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny from PUEBLO, CO
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Drive great stripped for ice eject. Heater bad
Loosened the 2 bolts 4 turns where it mounts inside the freezer. Lift maker off the bolts unplug 1 plug. Reverse to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Les from Fenton, MO
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Freezer icing up and refrigerator section not cold
Removed four screws for cover on refrigerator temperature controls, unpluged old timer and pluged in new timer. Replaced cover and screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry D from PETERSTOWN, WV
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
sometimes it would go into defrost and would not go back to cooling.
I called the repairman who diagnosed the problem as a thermostat then had to order a thermostat took about 2 weeks to get back and install (cost little over $100). did good for about two weeks and same problem reoccured. I decided it was defrost timer and ordered from this site for $19.95 including shipping. I got on ( you tube ) and got instructions(recommend you tube) for DIY install about 15 to 20 minutes. Has been running great for about 3 weeks. ( YOU TUBE IS GREAT FOR A DIY REPAIR ON ABOUT ANYTHING)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Hanover, ME
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Freezer frosted up, refrigerator compartment heated up
I removed the housing at the top of the refrigerator compartment that contained the reefer light and temperature adjustment knob. This required a small nut-driver. Inside, I found the old defrost control, unplugged it, unscrewed it with a Phillips screwdriver, and replaced it with the replacement part. Then I replaced the housing to its original position.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NEIL from OCEAN CITY, NJ
- Parts Used:
- 240505801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Switch that shuts out light when the door closed broke
Removed the screws on the piece holding the switch which is at the front of the ceiling of the refrigerator box. Removed the old switch and replaced it. Very simple repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curt from Maple Grove, MN
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Freezer too cold
Removed the housing with the light, 4 hexhead screws. This exposed the defrost timer, removed 2 hexhead screws, electrical connector and reassembled the unit.
Great resource and service, thank you.
Great resource and service, thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from RICHWOOD, TX
- Parts Used:
- 242252603
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
The fan had stopped spinning. According to the internet it should spin freely if I use my hand, but it wouldn't.
After pulling the fridge away from the wall and opening the paper backing on the bottom, I could see the motor. It's affixed to 3 metal ribs by 3 small screw/nuts. There is also a 12" wiring harness that led to a simple disconnect. Removing the disconnect and the 3 nuts was easy. However, there was no room to remove the motor with the fan attached. Between frame parts, the drip pan below, the ribs, and small, delicate copper tubing that can't get bent, it wouldn't fit thru any openings. So we rotated the motor inside the framework until the blade faced out, then reached in with a pair of needle nose pliers to remove the washer. Removing the washer is easy, it's just difficult to reach. With the washer off the fan was out of the way and very carefully (it was tight) the motor came out. Reverse was the same issue. Motor tight going in, not a lot of room to maneuver fan onto motor, and needed needle nose to tighten washer again. Make sure you tighten the washer before you install the motor on the prongs. Otherwise you need to remove it from the ribs, twist it to face you, then reinstall it on the prongs. Also, I felt I was stripping the nuts into the new motor. Turns out the holes in the motor aren't tapped. i realized the nuts are self tapping once I looked at them. I'm a big time DIYer and this wasn't bad at all. If your motor/fan assembly comes out whole, it's even easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobbie from ARLETA, CA
- Parts Used:
- 242193213
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
The door gasket was not working at all
I watched and followed the instructions on YouTube ?? very easy
Was this instruction helpful to you?
Thank you for voting!