CRTE217IAQ1 Crosley Refrigerator - Instructions

Turned off fridge circuit breaker
Removed all food from freezer and put in cooler.
Removed shelves from freezer
Removed ice maker
Removed 2 hex head screws
Tilted back evaporator cover and tried to unplug connection.
Found connection was iced over with a huge block of ice coming from water inlet to ice maker
Spent several hours trying to melt and chip away ice without damaging fridge.
Finally was able to break up ice with long flat head screwdriver and hammer.
Unplugged connector and was able to remove evaporator cover.
Cut wires near thermostat and removed
Stripped wire as needed and crimped new thermostat in place.
Used heat gun and lighter to melt heat shrink. This took a long time and required a lot more heat than expected.
Reconnected evaporator cover connection and reattached cover.
Reinstalled ice maker
Reinstalled shelves.
Put food back in
Turned circuit breaker back on.

A little difficult getting out due to restricted space, I took off the fan blade, that gave extra working room. Then it went well going back together,and it all worked as advertised. Thanks. p

1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.

It was real easy but I still have problem making ice cubs
Fell problem is in the ice maker went it dose make cubs they don,t dump

Unscrewed old bulb and put in new one

Turn off power. Remove ice tray. Back out the two screws with nut driver and just lift ice maker off screws. Do not bend the water fill tube in the back . Now unplug the wire and remove ice maker .
To replace, match the color of wires on plug. Adjust wires in place and water fill tube and back on to the screws. Hold in place and snug screws. Turn power back on. In 4 to 5 hours your ice will start .
FED-EX UT to MN was 13 days to deliver .

I emptied freezer side of unit, turned unit off, rolled unit away from wall, unplugged unit, turned ice maker water supply off, and took out the ice maker. I then took out old light and replaced it with new light. I then plugged in the unit, turned on the water supply, rolled the unit back in place, placed the ice maker back in the unit and turned the unit back on.
After two hours I placed the frozen items back in the freezer.

I remove the old fan by pushing it off the spindle toward the evaporator and put the new one on by holding it on the right side and guiding it on the spindle from the left side, very easy task

But I have back ground mechanical skills, I did see the video one time, and everything went smooth......

Looked it up on how to, follow the video
. Very easy 1-2-3 it was out and new one in..........??.

I tied in to your web site orderd the parts the part were here in a day 1/2open cartons expecting to be broke but to my suprised they were in great shape and then fit perfectly the first time love your company.

Looked up similar problems and found it to be the defrost timer. All I had to do was remove the plastic portion in the fridge section to get to the old timer. Popped the new one in and put it back together. Works great now. Would have been almost $150 to have a repair company come out and fix it.

I stuck a small screw driver under the old switch & it came out really easy. I just unplugged the 2 electrical connectors, and removed the old switch. Installing the new one was just as easy. I am a woman!

I also want to say how FAST PartSelect gets their items to you. It came in ONE day!

Your repair stories are very helpful, I/we would have never known how easy this switch was to replace! Thank you!

Opened the box, snapped it in place. Took longer to just open the box! I carefully inspected the part and compared to the original. I could not tell them apart. The fit and finish is perfect. This is a very well made product. Easy to order, fast shipping, well packaged and very easy to install.

Loosened the 2 bolts 4 turns where it mounts inside the freezer. Lift maker off the bolts unplug 1 plug. Reverse to install.