CRT216HLS1 Crosley Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sharon from Montague, MI
- Parts Used:
- 241872511
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
moved into a new home and the inside freezer was iceing next to the freezer gasket.
purchased a new freezer gasket. It is still iceing in the freezer but now all over the top part and down the back. The new gasket does not secure tight enough around the entire freezer door when it is closed. It is secured properly to the door but does not "grab" tight enough when the freezer door is closed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DANIEL from CAPE CORAL, FL
- Parts Used:
- 5303918202, 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
FREEZER COMPARTMENT NOT COLD ENOUGH (20 DEGREES)
REPLACED TIMER-DEFROST 215846602..REPLACED THERMOSTAT-DEFROST KIT 5303918202..REPLACED CONTROL, TEMPERATURE 5304421256..RECHARGED SYSTEM WITH 134A...ALL FANS WORKING...COMPRESSOR RUNS.. FREEZER STILL NOT GETTING COLD ENOUGH...HOLDING AT 20 DEGREES...ANY SUGGESTIONS..THANKS..DAN
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from Newberry, SC
- Parts Used:
- 5303918202
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
the freezer frosted up and the fridge was not getting cold.
I watched the instructional video and did what it said.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from SABINSVILLE, PA
- Parts Used:
- 5303918202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
freezer cold and frosting up but refrigerator warm
inside the freezer compartment, remove four hex head screws from rear panel,lift panel forward and unplug wire assembly from panel. find old defrost thermostat attached to copper tube by clip on back of thermostat, unclip, snip two wires to thermostat, take new thermostat, strip 1/4"of wire from wires in freezer (thermostat is prestripped),insert light blue wire from thermostat and light blue wire from freezer into opposite ends of crimp connector and crimp securely. repeat with dark blue wires. set panel back in freezer,connect plug to back of panel, refasten screws and you are go to go! save yourself the price of a new refrigerator or $300 repair by repairman!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shelley from KENSINGTON, NH
- Parts Used:
- 240364790
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Frame cracked and became brittle
Put old glass in new frame drop one side under small lip of frame..done..perfect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nathan from WELLS, ME
- Parts Used:
- 5303918202
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Refrigerator and freezer running to warm.
I watched the video on how to change the defrost thermostat. I removed the back cover inside the freezer then I pulled off the old defrost thermostat and then using a pair of wire cutters I cut it off and then bared a little of both of the wires and then slid the heat sherink and wire connectors on the existing wires and then slid the other ends of the wires into the wire connectors then crimped the ends of the connectors and then tried using heat on the heat shrinks but still used rubber electric tape over it. I clipped the new thermostat were the old one was and then reattached the freezer wall cover and plugged the refrigerator back in. 24 hours later I checked the temperature in the refrigerator and freezer and both are running a lot colder.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from ORMOND BEACH, FL
- Parts Used:
- 240505801
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light Switch not working properly
After unplugging the fridge, I took a small flat headed screwdriver and carefully pried off the light switch from the inside, right side of the refrigerator. I disconnected the 2 wires from the switch and replaced it with the new switch and pushed it back into the frame of the fridge. Done !! Very very easy !! Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ELENA from HOLLISTER, MO
- Parts Used:
- 240358928
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken plastic frame
Slid it in place. Waiting patiently for lower shelf that holds vegetable bins. We have duct taped the broken one together and it is holding for now. We would like an update on expected delivery date.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gary from ARANSAS PASS, TX
- Parts Used:
- 5308000010
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
I had a broken fan blade due to ice build up from a leaking ice maker.
1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JUSTIN from NEW BRAUNFELS, TX
- Parts Used:
- 5303918202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Top cools bottom is weak
Unplug, remove 2 screws off back panel inside the freezer. Cut wires on old one and crimped in new one. Light to melt the shrink wrap that came with it. Pretty easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from VAN WERT, OH
- Parts Used:
- 5303918202, 215846602
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Refrigerator not working, freezer working
I initially replaced the defrost timer, and later replaced it and the defrost thermostat. The defrost thermostat was the faulty component
Was this instruction helpful to you?
Thank you for voting!
we droppedthe crsper pan glass insert while cleaning the refrigarter and it shattered, the crisper pan ciover lip was chipped.
Easiest way to install was to insert the cover first then insert the glass insert being sure to tilt a little and inert under the shallow lip at the front of the cover. Not a good idea to assemble before inserting in the fridge. When cleaning the refrigerator shelves in the past I took then out of the refrigerator, cleaned them and re-installed in the method above. Just was not careful enough removing when I dropped the glass
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dari from ALBION, ME
- Parts Used:
- 240338201
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
replaced a broken door bin
just pulled the old one out, and plopped the new one in. I was nervous about the new one being the correct size, but it was perfect. No fuss, no mess.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erin from NEW ORLEANS, LA
- Parts Used:
- 241872514
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old refrigerator door gasket was warped and door wouldn't stay tightly closed.
No tools needed. Popped out old gasket, cleaned/sanitizeddoor and popped new gasket into grooves. Door now closes tightly!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margery from WOODBURY, NJ
- Parts Used:
- 241872514
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
rubber seal was wore out
just pull the old off and put the new one on the magnetic strip inside the rubber was the key it just grabbed the area real easy.
Was this instruction helpful to you?
Thank you for voting!