CT18AKXKT01 Crosley Refrigerator - Instructions

Replaced two parts that we got from Partselect.com and fixed it.

We just had to find the trick to put it in where it would catch on and the rest was a piece a cake.

You had to put it in the groove where it would catch and snap it in place and the rest went in
pretty easy.

Removed the lower back panel (10 small screws)Found the condenser motor froze up and not moving air across the cooling coils.So I got a small table fan and set it behind the fridge and it kept the fridge cooling for 3 days till the new fan motor arrived. Removed 3 small screws holding the fan motor in the bracket and unpluged the wiring harness.Removed the fan from old motor and used it on the new motor.Replaced the fan in the bracket and plugged the wiring harness back in. Worked great. Very easy.Did not have to empty fridge because table fan kept coils cool. Ordering part was easy and shipping fast.Great job guys!!

The only tricky part of ordering replacement drawers for this fridge is that the bottom ones are two different sizes so you have to be sure you order the right one. Measure the width and look closely at the exploded drawing to be sure you are getting the right one.

Removed 1/4 screw from housing to access thermostat. removed plastic tubing and three wires, reassembled and it works fine.
Repair took 12 minutes

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

We decided to use our crisper drawers to store sodas. Duh..bad plan. The rail that holds the drawers up cracked in half. So we just had the drawers sitting on the bottom of the fridge. So, I got the new rail THE DAY AFTER I ORDER IT! I just recycled the old one, and slid the new one in. Presto. Perfect fit. Actually, better then perfect. There must have been a defect with my old one, because the new one actually SNAPPED into place, instead if just sitting in the frame. So..I am really pleased.

changed the starter connected to the compressor

If I can do it anyone can. I'm a woman who is alittle handy around the house but if
i don't do it know one will.It was easy and only took about 10 minutes, 3 wires plugged into it and thats it.

its not that hard to replace. may need help to tilt fridge on one side so you can get to the bottom to remove wheel.Had to undo all four corner screws/bolts to loosen bottom section and slowly pull out base frame which holds the 4 wheels. this frame is also holding the compressor and fan so be careful.replace wheel and slowly put frame back to position and screw back bolts. pull back fridge to upright position. leave unplugged for a day or two to allow gas to come back to normal level as we had tilted it.plug it back and it works.
thanks
Anoop

I ordered the crispers and they came the next day.I took them out of the box and had them installed in about 30 seconds.It doesn't get any easier than that.The lady on the phone was very helpful when I placed the order.The fact that they came the very next day was amazing to me.

tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok

First, pulled knob off ot thermostat. Then, lowered control panel housing thermostat by unscrewing one screw. Removed old thermostat after taking off three wires. Replaced with new thermostat, secured wires, and screwed control panel to top of refrigerator. That's all it took. Challenge was finding the nut driver to loosen screw.

I deenergized the refigerator, removed the storage tray, three screws that hold the ice maker, two screws that hold the lower portion of the freezer, two screws tjhat hold the back portion of the freezer. Removed the ice maker and disconnected the wire connector and ground, Removed lower portion of the freezer which allowed the back portion to be lifted out. Once the back was out the bimetal defrost thermostat was located in the upper right corner clipped to a copper line. Using an ohm meter, I found the bimetal defrost thermostat to be electrically open, ordered part from information found on part, Once part arrived I deenergized the refrigerator and replaced bimetal thermostat by cutting the old thermostat wires (pink and brown), stripping the wires back about 5/8 inch and wire nutting the replacement parts like colored wires, clipped the bimetal part on the copper tube, replaced the covers in reverse order, and reenergized the refrigerator. Testing and replacing the part took about 15 minutes, waiting for the ice build up to thaw took considerably longer.

First, unplugged the refrigerator. Then removed bottom plastic liner of the freezer, 2 screws with 5/16 nut driver. At this point the ice maker had to be removed 3 screws, two on the upper part and the other under the ice maker. Now the back wall of the freezer section was removed by unscrewing 2 screws with the nut driver. This gave me access to remove the defective clip-on Bimetal defrost thermostat. It was located in the upper right corner on the back wall of the freezer. Cut off the 2 wires from the bad part( one pink the other brown)then used wire nut to replace with the new part and matched wires from freezer to new part( pink to pink and brown to brown) and clipped the part in one section of the coil. ( where the bad part was located) Put all back in place. And so far no more water leak inside the fridge.