CS21G5DQ Crosley Refrigerator - Instructions

Philips head screwdriver and ten minutes was all it took! I removed the two screws that hold the icemaker assembly in place, then pulled it out a little and disconnected the electrical plug freeing the icemaker assembly. Then I snapped the external parts off my old icemaker assembly and snapped them on the new icemaker assembly. Installing the new icemaker assembly was just as fast and easy. I snapped the electrical plug into the new icemaker assembly, then screwed in the two screws. It was making ice shortly thereafter. Glob free ice! I'm glad I didn't call a repairman. I probably saved a hundred bucks. A ten year old could accomplish this simple and easy task. No wonder the Maytag repairman has time on his hands.

After moving the refrigerator away from the wall I removed the cover on the lower back of the unit by removing the screws that held it in place. The condenser fan was not turning and there was heat build up in the area causing the refrigerator to not work properly creating elevated temperatures in both the freezer and regrigerator. Removal of three torx screws from the original motor was all it took to get the motor free. By turining it and working the fan blade around the mounting bracket I had the motor out in just a few minutes. Replacing the new motor was just as easy to reinstall. The fan was removed from the old motor and placed on the new for installation. The original motor was wired to accept a connector from the wiring harness of the refrigerator. I simply cut the connector off the wiring harness and stripped the insulation from the wires which easily allowed me to connet the wires of the motor and harness with two wire nuts. Three self tapping screws were used to hold the motor in place replacing the torx screws. Installed I plugged the unit in and immediately the fan started spinning as the unit came to life. Cleaned and replaced the cover over the back and slid back into its spot. Running as good as it did when it was new. Easy job to take care of.

Jenn-air jcd-2389gtw refridgerator/freezer side by side ice door would not open to dispense ice from the ice dispensor I did an online order for the repair kit #ps2003478 (115v) ice dispenser solenoid and door kit to fix the problem with the ice door not opening. As I had deduced, the “solenoid” had gone bad, and the kit held most all the items required to make the repair. The only additional item the kit needs to have is the “fountain door return spring”. Be careful not to loose the spring when disassembling the unit. You might want to order an additional spring just in case you loose or break the original. The instruction sheet was pretty thorough, except for being small and the pictures hard to see. My refrigerator/freezer has decorative panels that had to be removed before I was actually able to get the escutcheon off of the unit, and this configuration wasn’t addressed in the instructions. After figuring out that I had to remove all the trim from the door of the freezer before I could start the repair, the job wasn’t that difficult, but you have to have patience and take your time to make sure you don’t damage the electrical components of the ice dispenser. Make sure you note the position and location of the fountain door return spring before you remove the ice door!! This is important so that you can get the correct “tension” when reinstalling the mechanism. If there isn’t enough tension on the spring, the door will not seal properly, and the dispenser will freeze up. Also, when it comes time to disconnect the “electrical edge connector” from the control panel, be sure to make note of it’s position. It isn’t difficult to pull off, but could be easily broken if you are not careful. The rest of the repair and installation is straight forward and simple. Just take your time and it goes back together pretty easily. Tools you will need are; needle nose pliers, phillips screwdriver with a small and medium bit, and a “torx” tool set to remove the torx screws from the escutcheon and fountain bracket.

The new Ice Maker Assembly arived in less than 24 hours. I was amazed that it came so fast.

I had already removed the old ice maker in order to get the modle number.

I just took two parts off of the old ice maker and quickly snapped them into place on the new ice maker. Then attached it to the refrigerator in less than 10 minutes. With in a few hours I had ice again !!!!!

I would definatly use partselect.com again.

Removed housing on the freezer side and removed the assembly by removing the two bottom clips and then unclipping the wire harness, two prong, and replaced as remvoved. Power was off of course. Watched for 24 hours and recovered housing and its been working great.

I noticed that the thin plastic flap was missing. I squeezed the housing, unsnapped and pulled. INstalling the new part was just the reverse. No more frozen vegetables.

I removed the two screws that hold the element in place. I then unscrewed the four remaining screws with a star screwdriver and pulled the element out and disconnected the wire. I removed the part containing the solenoid, spring loaded holder and the plastic closer. I did not need to replace the solenoid or the spring loading device only the round circular piece that opens and closes the ice door. I just snapped it into the spring loaded part and replaced everything as I had removed it. It was very simple. Your need the star screwdriver though for removing the screws.

tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok

I unplugged the fridge. Loosened the 2 top screws on the ice maker and removed the lower screw. I disconnected the wiring harness and removed the Ice maker. I removed the plastic timer cover in front. I then loosened the screws on the face of the ice maker and removed the broken ice stripper and replaced it with a new one. Re-tightened the screws on the face, installed the timer cover, plugged in the wiring harness, re-attached the ice maker. Plugged the fridge back in and walla, it was making ice in 30 minutes!

This repair was relatively easy due to the instructions provided and took about 15 minutes. Originally, I had bought a door flap thinking that was the problem (a small plastic piece on the flap had broken off) but after replacing that the assembly still would not allow ice flow. I then purchased the kit including solenoid and the repair worked. I had a bad solenoid all along. My suggestion is to replace the entire kit rather than one part as it is likely all parts need replacement.

Unplugged refrigerator. Removed lower back access panels and panel running up the back of refrigerator. Removed and disconnected old fan. Removed old fan motor from mounting bracket. Removed fan blade from old fan motor and placed on new fan motor. Connected new fan motor to power supply. Tested. Reinstalled.

The old icemaker had a bad motor and would stall in the fill cycle causing my kitchen to flood on occasion.

The new one was so quiet, I thought it didn't work!

Anyway, one nutdriver and 5 minutes and I had the new one in there... It is so quiet, and I always have plenty of ice now!!!

Thanks!!!

I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.

Thanks,
Matt

First I unplugged the refrigerator, then next I removed the (4) screws holding in the inside back panel section of the freezer covering the cooling coils, the fan motor is attached to the removable panel.
I then unplugged the wiring harness to the fan motor which allows you to completely remove the freezer inside panel in order to replace the fan motor on a counter top or benchtop.
I removed the (3) spade terminal wiring from the fan motor and the nuts holding the motor on the frame. I then replaced the fan motor and blade the same way I had removed the old one, and then reattached the wiring terminals on the same terminals as the existing motor, making sure that black, red, and green do not get mixed up. I placed the rear panel back inside freezer and plugged in the wiring harness, fit panel back to original position and reinstalled the (4) panel screws. I once again plugged in the refrigerator and restored power. Everything is working fine.

My ice maker was overflowing and i realized that it was the water valve that needed replaced. unscrewed 1 nut, unhooked 3 water lines, unhooked electrical components and re-installed in reverse order. took about 10-15 mins.