CS26G7DQ (PCS26G7D0C0) Crosley Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Clifford from Madison, IN
- Parts Used:
- WP67007098, WP12665101, WP12562701, W10857122
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker door broke allowing open hole to freezer
The ice maker panel on the freezer door detaches by removing two screens at the bottom of the panel behind the drip tray. My son held the panel while I removed three screws holding the ice chute cover. The ice chute door is attached to a spring loaded bracket. I only needed the actual door, but it was just as easy to replace the insulation and the seal. The seal was starting to show wear. I then replaced the ice chute cover and tested the ice maker. With everything working correctly, I reinstalled the panel in the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fidel from Forest, MS
- Parts Used:
- WPW10128551
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Refrigerator wouldn't cool
First I removed the six screws from the cover. I then disconnected the two wires and pulled the small motor out with its base and removed two screws that hold it in place. I then changed the old one for the new one and set it back in its place. I then set the cover back and turned it on. I was happy again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Marion, IL
- Parts Used:
- D7824706Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
didn't eject icecubes
R & R Icemaker Assembly. Took out 3 screws and unpluged Icemaker & replaced with new part. very easy and the service from PartSelect was fantastic.
Very Satisfied,
Ron Martin
Very Satisfied,
Ron Martin
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Pennsylvania Furnace, PA
- Parts Used:
- D7824706Q
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Ice maker leaked water
Overall, replacing the ice maker wasn't too bad but it wasn't nearly as easy for me as it seems to have been for some. In my case, the fridge was an Amana and the ice maker was mounted in such a way that disconnecting the power connector was difficult. The ice maker had to be completely dismounted before any access to the power connector was even possible. The short power cables made it very difficult to get the ice maker into a position where I had a good view of the power connector enabling me to see how to release it. The only other challenge was the cup that the water line goes into. The replacement ice maker did not come with the right cup - the instructions said to replace the provided one with the old one. No instructions for this procedure were provided and it looked to me like it might involve significant disassembly, something I wanted to avoid for fear of breaking a plastic part on the new ice maker (something I had already done when disassembling the old ice maker). So instead of replacing the cup, I modified the new one to match the old one. This involved removing a cutout on one side and covering a hole on the other. Installation of the new ice maker went fine and the water leak problem was fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from The Villages, FL
- Parts Used:
- WP12740302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
The icemaker assebly would go off track
I removed the front cover--just popped off with no trouble. Removed 2 screws at the bottom. Slid the broken part out and put the new one in place. Put in the two screws, replaced the fron cover AND Done!!!
BTW I am a 65 year old woman and the icemaker is like new.
BTW I am a 65 year old woman and the icemaker is like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Knoxville, TN
- Parts Used:
- WP67002527
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Quit cooling ,had a click noise when it tryed to turn on compressor
removed the rear panel and replaced the part on the compressor and replugged the wires.Easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Cumming, GA
- Parts Used:
- R0181181
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Replaced door cam closer
Replaced the part--
Door snaps loudly everytime it's opened or closed.
Correct replacement part and lubed with vaseline,
Door snaps loudly everytime it's opened or closed.
Correct replacement part and lubed with vaseline,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emi from Arlington, VA
- Parts Used:
- W11395888
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
no water when under sink water filter installed
I called the installer of my filter unit and he told me that often, thhe fridge filter is the problem. Like magic it worked
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roderick from NEWTOWN, PA
- Parts Used:
- WP2300868
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Leaking water tube connector/union
Received the union I ordered, then discovered that the tubes were different sizes, so I had the wrong part. I had read elsewhere that it was necessary to trim the two ends of the tubes with a box cutter to stop the leaks - I did this, and the leaking stopped. I was then able to go to a local hardware store and get a 5/16 to 1/4 union and replace it. The leaking is stopped, and the water supply in the door is now working like new. No problem with partselect, but I did buy a caliper so that I can check tube diameters if I ever have a similar problem! This is a great site to find instructions - well worth the time to search!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- anthony from georgetown, IL
- Parts Used:
- WP628356
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken Piece
Had to disassemble ice maker to install part. . .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Deerfield, IL
- Parts Used:
- WP12740302
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Fridge missing agitator assembly and ice bucket.
While ordering the assembly, I had thought that the ice bucket was included but it wasn't. So I ordered the ice bucket afterwards. Maybe a little more clarity as far as what parts come in the whole assembly would save some time. All in all, the agitator was very easy to install, along with the ice bucket. After securing the agitator to the existing assembly with two screws, the ice bucket slipped right into place. Easy to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert C. from Milford, PA
- Parts Used:
- 12002193, WP12544002
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
no water pressure, and very little volume of water
First I removed the existing copper ice maker line and then installed a plastic line. I then tried the appliance, with no change. I then removed and replace the primary water valve and then tested that as well. There was no change in the outcome. So I removed and replaced the secondary water valve and tested that as well and I noticed a significant change in water pressure, and in volume.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Garden Grove, CA
- Parts Used:
- R0181181
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Replaced 1 broken door cam set
As the prior stories mentioned, this was a fairly easy fix to a nagging problem. Heck, we almost bought a new refer over this, cuz the door would keep popping open.
Needed a screwdriver, and a 5/16" nut driver (mounted in elec. drill). Have two people for this one! Emptying the door would help out tons too. ('course, I didn't do that!)
With the door closed, remove the plastic cover on top by removing 1 phyllips screw. Then, using drill mounted 5/16" nut driver, remove 3 hinge screws. Remove hing by lifting up. Now, carefully open and remove the door. Here is where the 2nd person comes in. There are 2-3 1/4" screws (Must use a 1/4' NUT DRIVER, SOCKET OR MAGNETIC BIT HOLDER) on the bottom of the door to remove the broken plastic cam. Also, you must remove the bad cam from the bottom hinge using I believe the 1/4" nut driver.
Finally , one person lift the door while the other kneels on the floor to help giude the door back onto the bottom hing pin. Close the door, ensuring that the top of the doors are even, and secure the 3 top hinge screws. UR done!
Greg
Needed a screwdriver, and a 5/16" nut driver (mounted in elec. drill). Have two people for this one! Emptying the door would help out tons too. ('course, I didn't do that!)
With the door closed, remove the plastic cover on top by removing 1 phyllips screw. Then, using drill mounted 5/16" nut driver, remove 3 hinge screws. Remove hing by lifting up. Now, carefully open and remove the door. Here is where the 2nd person comes in. There are 2-3 1/4" screws (Must use a 1/4' NUT DRIVER, SOCKET OR MAGNETIC BIT HOLDER) on the bottom of the door to remove the broken plastic cam. Also, you must remove the bad cam from the bottom hinge using I believe the 1/4" nut driver.
Finally , one person lift the door while the other kneels on the floor to help giude the door back onto the bottom hing pin. Close the door, ensuring that the top of the doors are even, and secure the 3 top hinge screws. UR done!
Greg
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacqueline from New London, CT
- Parts Used:
- WP67001036, W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
my freezer kept icing up and the light switch was broken
I carefully took the clear plastic piece out of the top of the refrigerator. I removed two screws, unsnapped the white plastic cover and unplugged the old defrost timer and plugged in the new one. I then replaced everything in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Herndon, VA
- Parts Used:
- 833697
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Condenser Fan Motor seized up
First I removed the back cover then removed 3 nuts holding the motor. Next I removed the two wires. Next I attached new connectors to the wires and installed the new motor and everything worked perfect!
Service and shipping were fantastic! I would definitely use Partselect again!
Service and shipping were fantastic! I would definitely use Partselect again!
Was this instruction helpful to you?
Thank you for voting!