CFEH272ITS Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Chuck from GRIFTON, NC
- Parts Used:
- 242220204
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Water outlet tubing leaking in elbow behind water filter
Most difficult and time-consuming part of the job was clearing the refrigerator of food and shelving. Replaced tubing as it had split in the factory bend of the tubing directly behind the water filter. Take your time and don't get in a hurry.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andres from Golden Valley, MN
- Parts Used:
- 241778315
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replaced door gaskets with new ones
Removed the old door gaskets by hand and attached the new ones by inserting the edges in the existing grooves
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Lancaster, SC
- Parts Used:
- 241778315
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
GASKET WORN AND LEAKING
SIMPLY REMOVE THE OLD GASKET PULLING LIGHTLY BY HAND
THEN PUSHING THE NEW GASKET BY HAND
THEN PUSHING THE NEW GASKET BY HAND
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Hampton, NH
- Parts Used:
- 5304537408
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
Previous seal had a tear and cold air was leaking around seal
Pulled the old seal out of the groove. Placed new seal in the groove. New seal has to be heated and massaged to get it into proper form so it does not leak. I have been continuously heating and massaging to get the seal to get it in the proper form. Been working on it for a week. Almost there.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Lockport, NY
- Parts Used:
- 241639502
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One blade broke from condenser fan
The part i recieved, from parts select was a larger in circumfrence (<1/4) than the original. However i was not aware of this until after i treid to repair it.
I removed the broken fan from the condenser. This was very sipmle.
When i pluged the refridgerator back in to the outlet the fan tried to start up but soon began to make aloud noise, due to there not being enough clerance.
I removed the broken fan from the condenser. This was very sipmle.
When i pluged the refridgerator back in to the outlet the fan tried to start up but soon began to make aloud noise, due to there not being enough clerance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BO from SUN CITY WEST, AZ
- Parts Used:
- EPTWFU01
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
No problem - just replace every 6 months!
Just place new filter and lock it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lorena from HOQUIAM, WA
- Parts Used:
- 242071301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
We had a broken bin on one of the doors.
We just slide in the bin.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from MAGNOLIA, AR
- Parts Used:
- 241675704
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
ice maker is stuck on crushed ice.
We had someone to come and look at it and we were told it was the solenoid valve. The repairman unstuck it for us and said when it does it again, he would have to order the part. We took it upon ourselves to order the part and DIY. We replaced the part that we were told was the problem and "guess what" it's still not fixed. It's still shooting out crushed ice. Will have to call repair guy back out here to see what we did wrong.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lewis from JONESBORO, GA
- Parts Used:
- EPTWFU01
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Was time to replace my water filter
Twist to remove the old one an twist to install the new 9ne
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward D from YOUNGSTOWN, OH
- Parts Used:
- 5304508033, 5304508016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
roller broke off
remove drawer , remove top shelve remove and repleace side rails ond take rollers off and repleace rollers. not bad at all
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daune from OCALA, FL
- Parts Used:
- 241675704
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Ice Maker was making ice erratically
After sending PartSelect the info to their troubleshooting dept. about my ice maker, they recommended replacing the ice solenoid. I did so at a cost of $102. No change, turned out replacing the ice maker(did not purchase from PartsSelect) was the issue and works fine now.
So wasted $102. FYI the part took 6 days to arrive.
So wasted $102. FYI the part took 6 days to arrive.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from Pawleys island, SC
- Parts Used:
- 242253002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Refrigerator water dusoeswr stopped working
I removed the defective water valve. All wiring and tubing connectios were color coded.
It connected the water tubes and electric plugs to new water valve.
The water dispenser worked perfectly after I reconnected everything.
It connected the water tubes and electric plugs to new water valve.
The water dispenser worked perfectly after I reconnected everything.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pam from HURRICANE, WV
- Parts Used:
- 242093003
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Ice maker had stopped crushing ice although it still made cubed ice.
Took out the old ice container assemblyr and put in the new one. No installation was required. Just replaced it in the ice maker housing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Orange, CA
- Parts Used:
- 242093006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The plastic part broke off. A known issue
Easy to install. Just make sure to line up the back pin. Also ensure your ice is adjusted to the correct amount of your daily usage.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from FREE SOIL, MI
- Parts Used:
- 243297613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Original ice maker not working leaking water water out door
Removed exterior housing, sliding old unit forward to release. New unit went in easily. Caution wires don't get pinched.
Was this instruction helpful to you?
Thank you for voting!