GFD160 Caloric Refrigerator - Instructions

Moved fridge out from wall, unplugged power cord. Laid on floor, removed 6 screws from cover. Removed one threaded bolt to allow assembly to slide out. Removed special nut, and took fan off. Removed 3 motor mounting bolts. Unscrewed 2 wire nuts, and untwisted wires. (option 1, no ground) Vacuumed entire area around motor. Used 3 bolts to mount motor to holder assembly, and special nut to install fan. Stripped wires back about 3/4 inch. Twisted two wires together CW, and installed new wire nuts. Slid motor assembly back into slot,(keep wires away from blades) and used one threaded bolt to secure assembly. Reinstalled cover plate with 6 screws. Plugged power cord in to test air flow (out through cover vents). Moved fridge back into place. The loud whirring noise did not stop for a day; then quiet!

Ordered timer-defroster motor and replaced. Very difficult to remove the two screws since there was little room to apply the tools.

The kit I recieved was perfect. All parts fit and where a perfect match. I will give you an A+ in handling my order and shocked by speed of your delivery.

I would like to say first of all that I was amaized and pleased at how simple the ordering of this part was and while looking at the parts diagram on you website I noticed the door swing was optional and could be easily changed and the dryer came from the factory with a latch installed on both sides of the door. In our laundry room the dryer sits to the left of the washer and the door to the dryer opened to the right which has always been a slight inconvenience. . . So instead of changing out the broken part, I took the door and hinge off with my cordless screwdriver (6-8 screws) and turned it around and remounted it on the opposite side. . . Simple! I never took the new part out of the ups envelope. Now I have a spare so I taped the new part in the envelope to the back of the dryer in case I ever need it and now we have more convenience with the door swinging the correct way. Sweet deal! Took less than an hour. Thank you for making this task simple. Chuck g.

Push new catch in the opening, close the door and VOILA! the door stays closed. Please note that the cost of this part is exorbitant- it's worth about 50 cents but with shipping it cost about $11.00. Check your local hardware store first.

Pulled out the broken part than easily snapped the new part into place..

Pushed in the Door Catch, and it was fixed.

After ordering the part, I read the information left by other users. I used a screw driver to pop out the piece, and then put the new latch in the opening. A gentle pop with the side of my hand, and the door latch went right into place. Who knew there was a second door latch on the other side that could've been used?

This was real easy just slid the latch in front panel and attached to latch assembly to the door. The repair was about 45 seconds.

Removed bad motor with socket set and pliers then removed the connectors from the old motor and soldered them on the new one. Then installed new motor. Works like new! Problem Solved! Easy fix!

I found the condenser fan was not working so I bought a new condenser fan kit and installed it. Fixed!

I have an Amana freeze and I followed the procedure in the video. Which is very good! However on the Amana Model there two slight differences in the procedure that I felt I needed to do. The first one is, the condenser fan bracket is attached to the Freezer chassis with 4 screws, not three. The removal and installation of the back screw by the fan is a bear. I removed the other three and it allowed me to rotate the fan slightly to get more access to the fourth and did same on installation by just starting the 4th screw and then tightening it later. The second issue was my new fan hit the housing when I spun the fan. When I looked at the old one. It had a phenolic washer, between the fan and motor which spaces the fan out about a washer thickness from the motor. When I tried to remove the old one it broke in four pieces due to age. So, I made my own with a washer that I super glued to the motor housing after carefully centering it on and clearing the motor shaft . Seemed to work with out any more noise or balance issues...Thanks, your delivery was blindly fast and video was great!

Well I could what laid on the floor and replaced it but I didn't I emptied refrigerator laid it over change the motor then stood it back up actual work about three hours

The video of the repair is a helpful guide, but my refrigerator has the compressor very close to the condenser fan motor. With the compressor comes the copper tubing that is all in the way. I had to carefully bend them now and then to allow me to get my hands in position. The how to is easy, but the working with tools in cramped quarters was difficult. I think my Maytag side by side model makes for this job to be difficult, maybe yours may not be so bad. I took a couple of hours to complete. After the first hour, I covered the bare wires, and plugged the frig back in so it could do some cooling. I placed a small in front on the condenser to blow across it. Had a little break, then finished the job.

removed condenser fan -located behind refrigerator next to compressor, Not much clearance to work, there are 3 screws to remove from condensing motor,sounds easy but clearance is lacking to remove them ,(takes alot of PATIENCE). Then you have to remove the fan blades to be able to get clearance to remove motor!! I wouldn't reccommend trying this repair unless you are a pro.