36591-P1108403W Amana Refrigerator - Instructions

Replaced ice maker but now water valve wont work

I read the previous repair story and agree with the author that the screw behind the front piece was difficult to remove and re-install. If I had a magnetized nut driver I think it would have been easier. There were no installation instructions so I relied upon the repair experiences. The other two screws came out easily and I found the harness release easily and the harness was easy to reinstall.
I am not a good handyman but was able to install the new ice maker

I made use of instructions for other users, see 'My ice maker has been shedding.....' and they were very helpful. The one problem not covered - the instructions that came with the new icemaker said to 'remove the bearing and inlet from the old icemaker and install in the new icemaker', but gave no instructions for how to accomplish this.

The old inlet has a square opening in the back and a u-shaped knockout in the side. The new one has a round opening in the side and square knockout in the back)

After several attempts to remove them, I gave up and used the new inlet with the knockout removed. I did not attempt to cover the side opening and it worked fine that way - no leaks.

Pop off six mounting screws and the ground screw. Remove the fan blade and reattach. Reinstall. Save yourself big bucks.

I removed the screws on the back of the refrigerator revealing the water valve, disconnected the water supply, removed the two outlet hoses and removed the bad valve. Replaced in the opposite manner.

Ice maker assembly required disconnection of the wire harness at the back of the freezer and the removal of 3 hex nuts. The assembly did not come with a new wire harness nor the rigid wire attached to the hinge that can be raised to stop production of ice. The wire harness was easy to disconnect from the old assembly by pressing in on a tab. The rigid wire attached to the hinge simply required pulling straight out of the hinge-hole (no need to twist, slide, or perform other contortions...it does require significant force to remove, but it does pull straight out). It was simple to attach it to the new ice assembly. Reinstalled the 3 hex nuts and wire harness plug and was good to go....after waiting several hours! I was worried at first because the unit did not immediately fill with water after I plugged the fridge back into the wall socket. However, after the freezer was cold enough, the water did run and I had my first ice dump within about 3 hours of finishing the installation. We have good ice again, and Partselect has excellent pricing and awesome delivery! I received the unit the day after ordering, and I had only paid the basic shipping! Thanks Partselect! Jeff

There are basically three screws that hold the unit in place on the inside of the freezer. Removing them is relatively easy, and the unit is replaced with the same three screws. You do have to use the formed metal wire from your old unit, so don't throw it out! You also have to use the wiring harness from your old unit.

Instead of the ice maker unclipping from the wall after one 1/4" screw being removed from the bracket, I had to remove three of the 4 Phillips head screws from the ice bucket slider below the ice maker and swivel it down to allow the ice maker bracket to clear. The two 1/4" screws holding the ice maker to the wall at the top had to be removed and then the ice maker could be pulled away from the freezer wall. The rest of the instructions went according to the video and went well.

Replacing the icemaker is pretty simple. Three screws, an electrical connector. Hardest part is getting to the icemaker since the freezer is below the refrigerator.

It's self-explanatory. The procedure is obvious; it's just a little difficult. The only hard part is attaching the mounting brackets to the fan. If you can't tighten the mounting bolts, loosen them and reposition the brackets. You might end up mispositioning them at first, because they are hard to reach.

First I removed all the screws from the back cover.
2nd removed fan nut and fan blade
3rd removed fan bracket
4th I traced wire to the condenser and disconnected wires from wire nuts.
Installed existing fan brackets to new motor kit
then reconnected wire nuts to new motor cord
Reinstalled fan nut and blade,
reinstalled cover, plugged it in and BAM .WORKS PERF!

I removed the back cover, disconnected the water line from the valve and unplugged the wires. I went to the Parts Select website and entered the info on the part (Plastic, Electrical) and brought up several beautiful pictures that immediately allowed me to identify and order the part without ANY part or model numbers! Wonderful! 3 days later, I installed the part in reverse order and the icemaker works like new again. Thanks for making it so easy!

Loosen the screws on the sidewall (don't take them all the way out and drop them on the floor as I did) and remove the screw from the bottom bracket. Change out the electrical wires and the wire level sensor that does not come with the new unit. Put the new one in place and give it some time to cool down and make ice ( don't be impatient like I was and think the new unit was bad or that you replaced the wrong part)

Moved frig away from wall, unpluged and took off lower back panel. Disconnected water line and ice maker lines from water valve (after shutting water off). Removed 2 screws, New valve was exact replacement. With new valve in hand, I removed electrical connecters one at a time and placed them on new valve. Put new valve in place, inserted 2 screws and tightened, Connected water lines, checked for leaks, moved frig back in place, job complete. No more drips, worked perfect. Total time, about 30 min.

1. Moved the firdge out so I had room to get bhind it.
2. Un-plugged the fridge so I didn't get electrocuted.
3. disconnected the the water hose from the broken water inlet with adjustable wrench.
4. Put hose in bucket to drain and moped up water from inlet valve with towel.
5. removed the 2 scrwes with socket driver that holds inlet on fridge.
6. reached in behind the inlet valve and unplugged the wires from the inlet valve (total of 2 plugs)
7. pulled the inlet valve out of the back of the fridge.
8. removed the bolt that holds the ground wire the metal plate that the inlet valve was connected to.
9. removed the defective inlet valve from the metl plate and tossed the defect valves.
10. put the metal plate on the new inlet valve.
11. screwed on the ground wire to the metal plate from new valve.
12. plugged in the 2 plugs back onto there proper locations on the inlet valve.
13. put the assembly back into place in the back of the fridge and screwed in the remaining 2 screws to hold it in place.
14. Put plumbers tape around outside of inlet to reduce leaks.
15. re-attached the hose and tightened it with the wrench.
16. turned on the water from the wall and verified there were no leaks.
17. Plugged in the fridge and tested that the water on the door worked.
18. Pushed the fridge back into place and the kids could once again enjoy water from the door of the fridge and in about 5 hours we had some ice again for our drinks.