ART2127AC-PART2127AC0 Amana Refrigerator - Instructions

Followed Youtube video from Free Repair Help. Only problem was getting down low enough to see the pins on the Compressor to plug the replacement Compressor Start Device and Capacitor-could not replace the old clip to hold the unit to the Compressor like the old unit had. At 77 I just have a problem bending over.

I made use of instructions for other users, see 'My ice maker has been shedding.....' and they were very helpful. The one problem not covered - the instructions that came with the new icemaker said to 'remove the bearing and inlet from the old icemaker and install in the new icemaker', but gave no instructions for how to accomplish this.

The old inlet has a square opening in the back and a u-shaped knockout in the side. The new one has a round opening in the side and square knockout in the back)

After several attempts to remove them, I gave up and used the new inlet with the knockout removed. I did not attempt to cover the side opening and it worked fine that way - no leaks.

installed replacement ice maker kit. 1st removed power. next loosened 2 upper phillips screws. then removed lower phillips screw and lifted and removed old ice maker. released wiring connector and pulled entire unit out of freezer. then i reversed the procedure to install the old unit. check youtube for instructional videos.

Take off freezer door to take off refrigerator door. Once fridge door off, put freezer door back on, lightly screw in place. Lay fridge door down flat on table. Take out all screws. Put new gasket in, while putting a few screws in to hold in place. Screw down. Use blow dryer to help get any kinks out. Easier than I thought it would be. I think my door is a little warped, but the gasket was enough to make it seal. No more condensation, and the fridge isn’t running all the time. Thanks parts people! Haha.

Replacing the icemaker is pretty simple. Three screws, an electrical connector. Hardest part is getting to the icemaker since the freezer is below the refrigerator.

Removed doors and door panel and gasket , Clean and replase gasket,Had no problem installing gasket
It took about 45 minutes

I just followed the directions on the video of my specific model. Make a note of where to locate that video of your model, as there are many other videos of other models that can have different parts located in different areas and it can be time consuming finding the exact video you want again.
Also note that you must make mental or written notes on exactly what direction any parts you remove are facing, this can save huge amounts of time when reassembling.
I was worried that I might need other parts, but decided to do one part replacement at a time since this unit is a spare and no urgency to get it back working again. I found that the evaporator fan was the only thing needed! The fridge works like new again!

I removed the flat panel inside freezer & fan blades not turning. I removed 2 1/4” screws, unplugged wires took fan motor out & put that fan blade on new fan motor. Plugged wires into new motor replaced 2 bolts, reinstalled flat panel plugged refrigerator in & reset temperature controls. The next day checked temperature and was all done.

Very simple fix, remove 3 screws, two connectors to the old switch

to easy to describe, remove 3 screws and a wire plug then install new unite.
Works great
Thanks

Remove 3 screws, took top hinge out, fz door and inserted shim...done.

just cleaned it and put in place. I was really impressed as to how fast it was sent to me. I broke it on Nov. 1 and placed the order that afternoon and received the new glass on Saturday Nov. 3. I really appreciated that as I never expected it until the following week. Thank you for the fast service!

Took under 5 minutes. Removed two screws and unplugged the wire bundle from refrigerator. Removed old unit. Put old wire bundle on new unit. Plugged wire bundle back into refrigerator and remounted the new ice maker. Could not have been easier. Watched the video first, it was very helpful.

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

Unplugged the power, removed old icemaker by removing 3 screws and unplugging a small wire harness

Then i moved the wire harness off the old one to the new one, moved the end cover over to new one and plugged the harness back in and screwed it back in and turned it on

ALL FIXED!