GB2026PEKW Amana Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- LARRY from HUTTO, TX
- Parts Used:
- W10827015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Our deli drawer had a cracked cover window.
Extremely simple to replace the entire cover. Just had to press on the sides to remove the cover from the hinge pins, then reinstall.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alexander from Chicago, IL
- Parts Used:
- WP12656105
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Lid to pantry broke off.
It was very easy. I removed the two crisper drawers and the glass shelf above the pantry section. I removed two bolts with a nut driver and one screw from the slide track. I pulled out the broken piece and did that all in reverse. Took 5 mins tops.
Also I wanted to say I got my replacement part in two days with standard shipping.
Also I wanted to say I got my replacement part in two days with standard shipping.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stu from richmond, VA
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
fridge door switch did not work
I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!
Why didn't I order this part and do the repair earlier? Very simple.
Why didn't I order this part and do the repair earlier? Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Roseville, CA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door light switch disintegrated
Very simple fix, remove 3 screws, two connectors to the old switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kathleen from south yarmouth, MA
- Parts Used:
- W10827015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
pantry lid cracked
The broken one just popped out and the new one popped right in! This company shipped out the part I needed immediately I had it in two days!! I highly recommend them!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neil from E GRAND RAPID, MI
- Parts Used:
- WP12656018
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Bottom drawer access door hinge pin broke of pantry end cap - right side. The pin(knob) is a molded part of the end cap.
Removed two 1/4" screws from the end cap with the nut driver and removed it. Transferred a few pieces from the old end cap to the new. Reinstalled the new end cap and presto, job complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from BRANCHBURG, NJ
- Parts Used:
- 67006697
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Tried to level rear wheel without unloading bottom freezer and broke the long leveling bolt.
Unloaded refrigerator. Pulled refrigerator from wall. Removed bottom panel on back and replaced bolt. Reversed steps but leveled rear wheel before reloading.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from RICHMOND, IN
- Parts Used:
- W10827015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Door on the pullout lower "Pantry" had cracked
Part was pretty ubiquitous so plastic door pins part fits a lot of refrigs, no tools necessary, new part is flexible enough to bend slightly to fit over pins at side. Mine was a bottom freezer type.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brent from PRESCOTT, AZ
- Parts Used:
- WPW10503278
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Freezer not defrosting and making fridge run warm.
Super simple following the instruction video you posted. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marc from SEASIDE, CA
- Parts Used:
- WPW10503278
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
the freezer and refrigerator number would lower it self and eventually get to "-" and "-" essentially shutting it self off!!
I replaced the Control Board...
the two boards need to be installed first . than plug in the connectors
(refrigerator was unplugged of course.!) i plugged in the connectors first. and had to disconnect them. install the boards first. than plug in the electrical connectors.. strange for a day or two it still did not work properly and than one day. it started working ok 7 on the freezer and 3 on the refrigerator. I do not know why..
the two boards need to be installed first . than plug in the connectors
(refrigerator was unplugged of course.!) i plugged in the connectors first. and had to disconnect them. install the boards first. than plug in the electrical connectors.. strange for a day or two it still did not work properly and than one day. it started working ok 7 on the freezer and 3 on the refrigerator. I do not know why..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Goldens Bridge, NY
- Parts Used:
- WPW10503278
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Refrig. was not holding proper temp in refrig compartment
Remove light lens by pushing straight back (needs some oomph, but not too much). Remove control housing by prying spring clips in back of housing with thin screwdriver or knife. Remove old control board by releasing plastic clips on both sections and removing 2 wiring plugs. Be careful snapping new control board in ; the alignment of the 4 switches and the 2 readouts is critical - easy to hang up a switch. Snap the control housing back into place, making sure that it is all the way in. Position the light lens so that it is lined up and about 1/2" back and then slide it forward (toward you) into place. The instruction sheet calls the refrigerator section the "fresh food" section. There are 2 light switches, one for each door. Both have to held down to get light to go out and enter programming mode. Easiest to close the right door, then push left door switch and quickly push the freezer DOWN button 3 times. Follow the instructions to set the program on the display and then push AND HOLD the freezer DOWN button until the display starts flashing. Release the freezer DOWN button, close the doors, open the doors to check. Display will indicate two 4s. (that was what mine indicated). Done.
Was this instruction helpful to you?
Thank you for voting!
Empty box sent with no part!!!! No customer service help because of covid
No product was sent in the box for the shaft I received an empty box from them cannot perform any repairs because I got no product from this company. Called customer service said due to Covid no customer service available when online and receive no customer service no refund no product no help
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from N SYRACUSE, NY
- Parts Used:
- WP12656018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dropped a jar onto the pantry and broke the plastic piece on end cap that moved the drawer lid.
Removed the lid and pantry drawer. Removed crisper drawer on right side and glass shelve. Removed 2 screws on glide. Removed 2 nuts with nut driver. Gently tugged on the pantry end cap and it released from the back wall. Had to rotate about 90 degrees to remove the extension off the back wall so I could remove the thermostat control arm from old piece and put it onto the new piece. Gently removed the thermostat control through a series of squeezing pieces and rotations. Do not force anything. Take your time as you are working with plastic that could break at any moment with force. Replace in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Oxford, MA
- Parts Used:
- WPW10503278
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Freezer cold ; fridge warm . Freezer not defrosting.
Unplugged fridge
Pulled light cover off
Used screwdrivers to press in on tabs holding control board cover.
Unplug wiring harnesses.
Snapped board in two.
Install in cover
Reattach wires
Done
Pulled light cover off
Used screwdrivers to press in on tabs holding control board cover.
Unplug wiring harnesses.
Snapped board in two.
Install in cover
Reattach wires
Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from MT PLEASANT, SC
- Parts Used:
- WPW10503278
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Fridge running warm
The fridge would occasionally run warm, requiring me to turn it off and defrost the evap coils in the freezer. I found an online video that demonstrated the entire process of replacing the control board. The fridge model in the video was different than mine, so it took some time to figure out how to remove the panel. Once that was done, the rest was easy. The only tool required was a flat-head screwdriver that was used to push in the tabs holding the panel in place. The circuit board took more effort to split in two than I had realized, and I had to be careful not to bend any of the components on its surface. The whole process took less than 30 minutes, and the fridge is working properly now..
Was this instruction helpful to you?
Thank you for voting!