GB2026PEKB12 Amana Refrigerator - Instructions

The Condenser Fan Motor was already removed due to searching for the problem. The new fan motor looked different from the original but I felt very comfortable that Part Select had sent me the new part showing original part number changing numbers over the years. Simply placed the fan blades onto the new motor lined up 2 of the holes placed screws and tightened then plugged the wire ribbon into the Condensor Fan Motor, plugged in the Refridgerator and it worked beautifully.

The instruction video on the Part Select Web Site made it so incredibly easy to install. Installation took under 3 minutes!

I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.

First, turn off the refrigerator so the open door alarm doesn't drive you crazy while you are working with the refrigerator doors open! Then, remove both crisper drawers, remove deli drawer, remove deli cover from two pins (one was already broken), remove the bottom glass shelf and the plastic glass support. None of this requires any tools, all just slide or lift out. Then, using a nut driver remove the two screws holding the drawer slide from the pantry end cap. You access one of the screws from an opening while the slide is all the way in. This is where I needed needle nose pliers to remove the screw from the opening after it was unscrewed - if your nut driver is magnetic you won't need the pliers. To access the second screw, pull the slide all of the way out. Then you remove the broken end cap by unscrewing 3 screws with the nut driver. Once the screws are removed, you lift up on the front of the end cap to loosen it from a catch on the inside and then pull the end cap out. Install the new end cap by sliding the two tabs into the back of the refrigerator and then pushing down on the end cap to set it in the catch. Now replace the screws, re-attach the slide with the two screws, reinstall the glass and the drawers and then reinstall the drawer cover by slipping it into the pins on each side (be careful when depressing the pins, do it gently or they may break off). Turn the refrigerator back on. You are done These instructions make it sound much more difficult than it actually is, it takes as long to remove and replace the drawers and it does to do the actual installation of the end cap..

Removed screws from the broken end cap and removed it. Installed the existing internal parts in the new end cap and reinstalled the screws. Very easy and the exploded diagrams on your site made it a very simple repair.

The switch fix but did not fix the problem. I assumed the wires go on the same way as on the old switch. Is it possible if one light Burns out, the other will not work either?

Removed the drawer and shelf above to get access to drawer slide. Removed slide with socket wrench. Also need to remove, then reinstall the arm that is attached to right side end cap that adjusts the temperature flow into the pantry drawer. Reattaching it was not obvious so it took awhile to figure out how it fit. Written instructions would have helped. The part did not come with anything.
This is the second end cap that has required replacing. The first was on the left so did not involve the temperature adjustment arm.

I am not handy; but the repair was really not difficult. I removed three screws that held the end cap. I removed the slide and the tempature control. Next, I assembled the slide and tempature control - a bit of time to figure out how it worked. Once that was done, I re-attached the end cap with three screws. Pretty easy, and my wife is happpy. BTW, the part arrived prompty and in great shape. I am very happy!

Everything went as planned except the cold temperature (freezer door switch located inside freezer) made deflection of the switch locking tab difficult to remove. Letting the switch warm up was not an option.

Checked Video online. Had to remove the 2 snap on track/gear covers. Pry out the gear with screwdriver and the gear bearing unit. Align the flat side of the bearing unit and snap in. Position the cut teeth on the gear to match original and snap into the bearing. Insert the connecting rod into the long shaft gear and then push back into the short shaft gear. The video said to remove the drawer front but I did not and don't see that it necessary.

Removed refrigerator door. Removed 3 screws. Replaced old ice maker with new ice maker. Put in 3 screws. Ice maker working great.

I followed the instructions for the installation of the icemaker and its connection to the house water supply.

I removed all of the drawers, and simply used the wrench set to loosen the three bolts holding the endcap and I used a screwdriver to loosen the plastic cover for the water hose. It took a minute or two to figure out how to unfasten the endcap from the other cover without snapping someother piece of plastic, but once I gently schimmied and squeezed the attached plastic the pieces came apart. Then it was just a matter of washing the refrig and replacing the parts. Snip/Snap.

Pried out the old switch and installed the new switch.

We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing

Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.