GB2026PEKB4 Amana Refrigerator - Instructions

It was great! Took my husband less then 5 minutes to fix. Your delivery time is excellent. This is the second time I order from you and would do so again if the need arises. Thank you so much. Don't be afraid people go ahead and order.

The new door just popped into place. Took seconds to complete. Fast delivery too.

Pushed on new one as directed online.

Popped out the old switch and replaced it with the one dying

extremely easy to replace, just snap off the white frame and snap on the new one.

First remove the snack drawer, glass shelf above it and other plastic pieces which just sit in place. Remove the three 1/4" screws that hold the end cap to the refrigerator liner. Lift up on the endcap and then out as there is a blind slot it slides into. Tilt the endcap out from the back and remove it. Remove the drawer glide from the endcap and transfer it to the new part. Reinstall the endcap by engaging the two plastic ends into the rear corner of the cabinet and then sliding it down on over the blind support. Install the three 1/4" head screws to secure the endcap to the liner. Reinstall the glass shelf and pantry drawer.

Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.

This has nothing to do with the repair - But with the customer service. I ordered and received a crisper in the mail and it had a crack in it. When I called the customer service # they helped me quickly and explained exactly how the credit/re-ship would happen. I received my new crisper in just a couple of days. Thank you!

The crisper only required me to remove the trim from the broken crisper and replace it on the new. The hinge on the deli cooler lid was more complicated. I had to take all the bottom drawers and shelves out, and then, using a socket set, remove several screws that held the old unit in. Then, perhaps most complicated of all, I had to figure out how to remove the temperature setting from the broken piece and replace it on the new piece. Once that was done, it was just a matter of screwing the piece back to the side of the fridge.

The switch fix but did not fix the problem. I assumed the wires go on the same way as on the old switch. Is it possible if one light Burns out, the other will not work either?

a) removed screws with nutdriver
b) took out old piece
c) disassembled good parts from broken piece
d) reassembled good parts on new piece.
e) reattached new piece
f) reattached door to crisper.

I did it quickly since this was the second time it broke. For easier access, remove the glass shelf above the drawer and the two plastic strips that hold it in place. Remove the two screws (yes, there are three screw holes on each side, but there are screws in only the front and center positions; probably to save money on screws) with either a flathead screwdriver or a socket wrench, which works better. There are two tabs on the end cap that slide into slots in the back of the refrigerator. There is also a plastic retainer on the side of the refrigerator in the front that attaches to the end cap. Gently lift up the front of the end cap and pull forward to remove it. Then unscrew and remove the metal slide bars and install them on the new end cap. Then do everything in the reverse order. Fit the two tabs into the slots in the back of the fridge, then position the fitting over the plastic retainer on the side of the fridge, and gently push back and down. Then screw the end cap back in place. Repplace the two strips for the glass shelf and then slide the shelf back into position. The last thing is to refit the tray door onto the tabs on both end caps. Slide it into position onto one end cap tab, then GENTLY push the tab back on the other side and fit it into position on the tray cover.

This sounds more complicated than it is, but there are no instructions with the replacement piece, which in my opinion is bad for customer relations. This is also a really bad design. If you accidentally leave the tray door open when you close the refrigerator door, the refrigerator door will hit the tray door and break one of the tabs.

Removed the drawer and shelf above to get access to drawer slide. Removed slide with socket wrench. Also need to remove, then reinstall the arm that is attached to right side end cap that adjusts the temperature flow into the pantry drawer. Reattaching it was not obvious so it took awhile to figure out how it fit. Written instructions would have helped. The part did not come with anything.
This is the second end cap that has required replacing. The first was on the left so did not involve the temperature adjustment arm.

The glide was very easy to put on; however it is easiest to put in the front screw first, due to the thickness of the glide. Pretty easy!

Removed the broken parts and freplaced it with the new ones. All it took was a little time and patience, to gently remove and replace both parts. Refrigerator looks like new. Easy Instructions to follow.