Models > TZ22QL-P1114906WL > Instructions

TZ22QL-P1114906WL Amana Refrigerator - Instructions

Jump to:

All Instructions for the TZ22QL-P1114906WL
91 - 105 of 269
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Jill from FALL RIVER, MA
Parts Used:
D7520510
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
The clips broke off our old one , I glued to many times
Opened new kickplate from pkg and snapped it on !! So happy
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from Colorado Springs, CO
Parts Used:
WPW10662129
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
freezer and refrigerator compartments not cold enough
Used the suggested problem list here to narrow down that the repair was most likely the run capacitor. Poped the new one in and I now have better control of my compartment ranges. I have a temperature gauge in each compartment. Check them every opening of the doors.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from Genoa City, WI
Parts Used:
10253508Q
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
broken ref. handle
with a phillips screwdriver I removed the old handle and replaced it with the new one. Very easily done. The parts I ordered came when I was told they would. The whole experience was a "piece of cake".
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Barbara from Shelton, CT
Parts Used:
D7520514
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
grille toe plate broken
I removed the old grille toe plate and snapped the new one in it's place.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Debbie from Salisbury, MO
Parts Used:
WP10253523Q
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Broken handle
After popping off the lower cover all I needed was a screwdriver to remove both the upper 2 screws and the lower screw. The new handle was attached in seconds and it matches great.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Carolee from Spokane Valley, WA
Parts Used:
W11384469
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Light switch broke
Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Murray from Medford, NJ
Parts Used:
10253510Q
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Original door handle was broke at the top.
Removed 2 screws from top and removed bottom cap cover to access the bottom two screws for its removal. Replaced handle by using the same screws and put back the small plastic cap cover and DONE.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mr & Mrs Robert G from San Marino, CA
Parts Used:
10253510Q
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Pieces of plastic had broken off the door handle
Replacement was extraordinarily easy. It took about 5 minutes, including the time to find my tools and put them away after I was done. As others have warned, only the handle itself was shipped. The trickiest part was being careful not to break the little plastic cover at the bottom of the handle when I pried it off. Apparently a screwdriver under any edge would have worked okay. There were three Phillips-head screws (replacements were not included in the package!) - and that was it.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gregory from Wildomar, CA
Parts Used:
10253510Q
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Top of door handle cracked
Removed old handle with a total of three screws, two on top and one on bottom of handle. Replaced with new handle and put existing screws back in place. Very easy!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from HELENDALE, CA
Parts Used:
WPW10662129
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
freezer would not freeze
inst said,"50 pct of the time this calls for new capacitor," so we changed the capacitor. Same prob. It also said,"25 pct of the time it's the bi-metal thermostat" So we ordered it. We removed the plastic rear panel from inside the freezer comp. using small nut driver. Here we found much ICE surrounding the defrost unit, three inches thick. We thawed the whole mess. and the freezer has worked fine ever since. I think my habit of getting ice cubes from the inside container rather than from the ice cube dispenser, had kep t the freezer door open too much, interfering with the normal defrost cycle and allowing ice to build up over time so that it finally defeated the system. My new rule, "get ice cubes only from the front."
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paul from Lowell, MI
Parts Used:
833697
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Socket set
original motor stopped
removed old and instaslled new. biggest problem was getting to one of the screws.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from Cherokee Village, AR
Parts Used:
WP10442411
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
freezer would not defrost
remove ice maker vent and back piece. Unclip defrost thermostat and unplug. Plug new thermostat in and clip to element, reattach back piece, vent and ice maker. Is a tight fit getting icemaker out, there are 3 screws 2 on top and one on bottom.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Douglas from Mesa, AZ
Parts Used:
833697
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers
Condenser fan motor froze up
Unplug fridge, unpluged fan motor from plug socket, removed bracket screws, removed fan retainer clip from shaft. removed screws holding fan to bracket
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
George from Belhaven, NC
Parts Used:
833697
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
cooling fan quit
Ordered new fan motor on line took out old motor and replaced with new one
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joseph from Lynbrook, NY
Parts Used:
WP10442411
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Refrigerator evaporator core iced up
I checked your web site for similar problems. Most were the bimetal defrost thermostat. Some had defrost timer problems. Althought my bimetal thermostat was deformed by the ice I replaced both parts. The fix was easy after defrosting the evaporator. By using the spec sheets I found the locations and replaced the parts. The refrigerator is now working fine.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the TZ22QL-P1114906WL
91 - 105 of 269