TZ18Q2E-P1156103WE Amana Refrigerator - Instructions

Very simple fix, remove 3 screws, two connectors to the old switch

Pop off six mounting screws and the ground screw. Remove the fan blade and reattach. Reinstall. Save yourself big bucks.

It's self-explanatory. The procedure is obvious; it's just a little difficult. The only hard part is attaching the mounting brackets to the fan. If you can't tighten the mounting bolts, loosen them and reposition the brackets. You might end up mispositioning them at first, because they are hard to reach.

Removed the old. Took off the name plate from the old handle. Put the name plate on the new. Installed new handle.

easy repair and looks great!!!
Thank you from a single Mom:-)

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Removed a small cover plug on the lower portion of the handle, removed three screws. Took off old handle, positioned the new one, replaced the screws and cover plug and that was it! Wouldn't have taken even 15 minutes if I hadn't dropped a screw and had to search for it - lol.

First I removed the old handle by removing the 3 screws holding it in place. There are 2 on the top and 1 at the side of the door. When I began to put the new handle on it became apparent that the metal frame inside the handle was not aligned perfectly with the old screw holes. The plastic is not even with the door horizontally on the top, but it fits otherwise. Be careful not to over tighten the screws when installing. Pretty easy overall.

Removed old handle. Cleaned area. Installed new handle. Remember to save small cover at bottom of old handle.

I got the product very quickly. (thank you) Looked at online instructions that were quite vague. Pulled plug.Removed the holder for the fan motor slid it out to see what I had. Removed the mounting screws (3) and slid the motor an fan blade out. I made a cut between the wires and marked the "top" wire to motor to be sure to spin in right direction. Removing fan blade hold down clamp was NOT explained at all but I noted that the shaft on the motor was threaded, so I used pliars and held the shaft white un-screwing clamp. I cleaned the fan blades with degreaser and scraped edges of opening on holder opening. Make sure to use ALL the NEW parts included with this kit when re-installing. They send them for a reason. When slpicing and connecting wires it is a 50/50 shot if you don't mark before cutting. You can connect and try plugging fridge back for moment and make sure it is blowing OUT. Put everything back together and after turning DOWN the thermostats twice, fridge is back to usual. Ice maker is cranking out ice and outside case is cool to the touch.

Note: This can be a DIRTY job especially with 4 dogs in house. Fir and grease don't mix well

removed 3 phillips jead screws. removed old hangle. cleaned around the site of old grime./ smile. positioned new handle, applied the 3 screws, tightened, and " whalah" like new.

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

****Make are you order Capacitor & Starter relay too (we ordered separtely so had to pay shipping twice)**** Super easy just open access panel on back near compressor and remove retention clip with fingers, remove & replace both capacitor & starter, put clip and access panel back on, plug in and allow 8 hours to cool! Works like new again! Hope it goes another 10 years