SL22JB-P1116006W Amana Refrigerator - Instructions

I used the process of elimination. The freezer was cold but the fridge side was warm. The motor was runing but the fan was not working. I unplugged the power cord and pulled everything out of the freezer. Then I took the coil cover out. The unit was frozen solid. I used my wifes hair dryer to melt the ice on the coil and spray water with a bottle to speed up the process. It took about 15 minutes to melt the ice and plug the power cord again. The motor kicked on and the fan started blowing right away so I know it's not the fan. The following morning it was frozen again. I repeated the process of taking everything out and tested the heater element with a multimeter. It wasn't working allowing the ice to build over the coil so I replaced it. It took about 30 minutes to replace but two days later it froze again. I read a little to learn about the timer and the thermostat function in a refrigerator. The timer rotates to turn off the motor and turn on the heater element to melt the ice on the coil. I tried to rotate it but it felt too hard to turn and it smelled burnt out so I replaced it at once. It took me less than 10 minutes to replace. I also learn that the thermostat reaches certain temperature and activates the fan which blows the cold air out of the coil and throughout the fridge compartments. Because the coil and the thermostat were getting covered in ice, it was not activating the fan to blow the air out keeping the freezer side cold and the fridge side warm. By replacing them both, the thermostat and the timer I solved the problem. It took about 30 minutes to replace the thermostat but now it's working like a brand new one again.

Partition between Freezer and Fridge was running very hot. (Warm is normal). Oiling fan did not work. The only problems encountered in the replacement were getting fan out and in through coolant lines, cut plug off to accomodate generic fan wiring, getting the screws back in without cooking your hand on a hot compressor. Unit works great!

removed lower back cover. diconnected fan ass'y electrical connection, removed fan housing (3 screws). removed fan motor from housing. cut old connector from fan and installed on new fan with wire nuts included. re-installed new fan to housing and re-installed housing to frame.

Ordered new fan motor on line took out old motor and replaced with new one

I removed the nuts that held the motor mount, then removed fan blade, cut the wires, and slid the motor pass the mounts and the coil shroud, Installed motor in reverse order. worked out ok.

Pulled out the refrigerator and removed the two panels from the rear of the refrigerator. Removed the fan held in by four screws and unplugged the connector. Soldered on the original connector, installed the fan to the motor and re-installed the unit into the refrigerator. Then blew out and vaccumed the condenser coils.

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

Removed rear cover to see non-operating fan - removed three mounting screws on the motor that were a challenge to access. Swapped fan from old motor onto new motor - one threaded nut on the motor shaft. Spliced new fan wires into fan wires of the wiring harness and mounted with three self-tapping screws supplied with new fan motor. Replaced rear cover and plugged it in! Now the refrigerator cools like new (1981 model side-by-side Admiral)

Based on internet research, determined that the problem was likely the defrost timer or the thermostat that's clipped to the cooling coil behind the freezer. Once before, a repairman had replaced the thermostat only, so that was my first repair. Still not working right, so I replaced the timer as well, and everything's working. I opened up the old timer switch and found the contacts were burned, partially arced.

If you have a similar problem, replace both parts. Only about $15 apiece

Very easy repair. Remove 2 nuts that keep timer cover on regrigerater. Remove 2 screws that hold timer to cover, unplug wires from timer. Install new timer.

With guidance from this web site, I was able to repair this myself very easily

Used a screwdriver to pry loose the old switch, swapped wires to the new switch and pushed it into the opening. Took about 2 minutes.

This is the easiest repair to perform, figuring out what was wrong took a little longer. I have the bottom freezer Amana refrigerator and the defrost timer is just behind the bottom front grill, removing four screws and plugging in the new timer took maybe 15 minutes. To find out what was not working correctly I removed the panel covering the coils in the freezer and it was totally frozen up, this is why it stopped making ice and wasn't keeping things cold. I defrosted the coils and checked the resistance of the heater to make sure it was working, it was fine so it was the defrost timer.

Removed the kick plate then removed four screws and unplugged the old timer. Plugged in the new part and replaced cover and kick plate.

Great service. Unpluged old switch and pluged in new one. Works great