TLC16V-P1311801WW Amana Refrigerator - Instructions

Super easy to repair. Just placed the glass back on shelves. Perfect fit!

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

I got the product very quickly. (thank you) Looked at online instructions that were quite vague. Pulled plug.Removed the holder for the fan motor slid it out to see what I had. Removed the mounting screws (3) and slid the motor an fan blade out. I made a cut between the wires and marked the "top" wire to motor to be sure to spin in right direction. Removing fan blade hold down clamp was NOT explained at all but I noted that the shaft on the motor was threaded, so I used pliars and held the shaft white un-screwing clamp. I cleaned the fan blades with degreaser and scraped edges of opening on holder opening. Make sure to use ALL the NEW parts included with this kit when re-installing. They send them for a reason. When slpicing and connecting wires it is a 50/50 shot if you don't mark before cutting. You can connect and try plugging fridge back for moment and make sure it is blowing OUT. Put everything back together and after turning DOWN the thermostats twice, fridge is back to usual. Ice maker is cranking out ice and outside case is cool to the touch.

Note: This can be a DIRTY job especially with 4 dogs in house. Fir and grease don't mix well

First I completely emptied out all the inside of the refrigerator door to lighten the weight of the door. Then I removed the 3 screws on top of the fridge which held the door in place. It was pretty easy to lift up the door and remove it from the bottom hinge. I removed and replaced the door closure and re-assembled the door.

Unfortunately that didn't fix the issue. The door still doesn't close on it's own. The door doesn't get lifted up at all when I open it so I assume that the counterpart to the door closure within the door itself is broken.

figured out the condenser fan was kaput. Tried WD, worked for several days then gave out completely. Took off back of fridge and trained small fan on compressor while I ordered new condenser fan. The swap was easy, undid the housing bolts, stripped off the connector, reconnected and voila! works perfect.

First I removed all the screws from the back cover.
2nd removed fan nut and fan blade
3rd removed fan bracket
4th I traced wire to the condenser and disconnected wires from wire nuts.
Installed existing fan brackets to new motor kit
then reconnected wire nuts to new motor cord
Reinstalled fan nut and blade,
reinstalled cover, plugged it in and BAM .WORKS PERF!

I unscrewed about 20 screws from the door, took out the inside, cleaned it first, then put the door gasket on, Screwed the door back in place.

I removed 7 screws hold the heavy cardboard cover on the rear of the fridge. The dificult part was taking the screws that hold the 3 fan motor braces on the fan out. After that it was a matter of making the wire conections and putting it back in. I did not have enough room to laydown to do the work, If i had it would have been a lot easier to see the screws that had to be removed. All in all an easy job, and the part was a perfect fit.

Unplug fridge, unpluged fan motor from plug socket, removed bracket screws, removed fan retainer clip from shaft. removed screws holding fan to bracket

I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.

I did not remove the door from the fridge deciding to replace the gasket while the door was still attached. Next time I will follow their suggestion to remove the door and lay it down. I didn't realize that when you take the screws out (And there are A LOT of screws!) the whole panel comes off the door. It also took a long time to clean the door and panel with years of dirt/mildew to deal with. I had a hard time trying to get the kinks out with a hair dryer, didn't seem to work. Putting the new one on and screwing it back in place was pretty easy (would have been easier if it was laying flat). There are a couple of places where the seal is not perfect because of the kinks, but not going to worry about that.

did not remove the doors. did freezer first ,removed inner door planel install gasget on panel and reinstalled. the aloney problem i had was trying to resape the door gasget on the big door. which is still a little out of shape hopeing it will fall in line over time.

1) I took everything off the door.
2) I removed the door from the bottom because it was easiest doing it from the bottom
3) I layed the door on the table and proceeded to unscrew the panel that holds things
4) I removed the panel and the old gasket
5) I cleaned all around where the gasket was screwed to the door and we cleaned the panel and we cleaned the refrigerator where the seal touches the door.
6) I made sure it was all dry and I fitted the new gasket on the door and put the panel making sure it fit around the panel
7) I began replacing the screws starting at the second screw from the corner and I did all 4 corners then I proceeded to screw the screws further into the corner and finally screwed all the rest of the screws.
8) put the door back on the refrigerator.
Now be patient because at first when closing the door there are sections that you have to push on to make it seal and this can happens for about a week. But finally it seals.

Had wife remove all the food from the bottom of the refrigerator. Removed the glass shelf , two drawers and the frame that they all sit in. Removed old broken crisper rail and replaced it with the new one, after I installed the wheel that the drawer slides on. Put everything back in place then called wife to put food back in where she wanted it.

Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.