TX22V2E-P1306503WE Amana Refrigerator - Instructions

I read the previous repair story and agree with the author that the screw behind the front piece was difficult to remove and re-install. If I had a magnetized nut driver I think it would have been easier. There were no installation instructions so I relied upon the repair experiences. The other two screws came out easily and I found the harness release easily and the harness was easy to reinstall.
I am not a good handyman but was able to install the new ice maker

Removed doors and door panel and gasket , Clean and replase gasket,Had no problem installing gasket
It took about 45 minutes

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

Remove 3 screws, took top hinge out, fz door and inserted shim...done.

remove 3 screws,rotate assembly,depress lock on wire harnass connector,un plug harnass.remove old assembly,remove and transfer side cover and steel wire at front of assembly,connect harnass to new assembly,rotate into place,aling screw holes and install 3 screws.flip front steel wire down and wait for about 1 hour,first tray of ice will fall..all done.

to easy to describe, remove 3 screws and a wire plug then install new unite.
Works great
Thanks

Unplug wire harness back of fridge. Unscrewed 4 screws on guide for ice bin. then unscrewed two screws holding ice maker to wall of fridge. removed ice maker. then had to take front cover off (pull hard, it comes off) and remove wire harness plug from the ice maker. save this, front cover, and all hardware to re-use. reverse steps to reinstall, including wire guide that goes up and down to stop and start ice maker when bin fills. Have to put this into front part of ice maker correctly for it to work. make sure it is down so that it will produce ice. ice tray took a few hours to fill with water initially, must be on a timer or something.

As per instructions. Removed parts from old ice maker, and installed them on new one, Then installed it in the freezer. Works good.

Replaced ice maker but now water valve wont work

Pulled out old gasket. Removed inner door molding then fixed new gasket around the edges. Replaced screws around entire inner door and snugged gasket into place. Unfortunately, it seems that the new gasket's magnets were not so strong and the door tends to pop open easily. I suppose it is better than it was...we'll need to keep an eye on it and perhaps get a manual latch of some sort....

Very simple fix, remove 3 screws, two connectors to the old switch

just cleaned it and put in place. I was really impressed as to how fast it was sent to me. I broke it on Nov. 1 and placed the order that afternoon and received the new glass on Saturday Nov. 3. I really appreciated that as I never expected it until the following week. Thank you for the fast service!

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

I recently bought an old Amana refrigerator for my garage on CraigsList for 75 bucks. It was in great condition for its age, but was missing the post that supports the fruit and veggie crisper drawers. I did a Google search, quickly found PartSelect, and just as quickly located and ordered the missing part, which was reasonably priced. PartSelect promised it woud be delivered in 3-5 days by FedEx Ground and it was. I took it out of the box, removed the crisper backets - and glass cover for them - installed the post and WHA-LA, the crisper backets work just as good as when the fridge was new! Couldn't have had an on-line mal-order operation go any slicker!

Removed the old. Took off the name plate from the old handle. Put the name plate on the new. Installed new handle.