SRD522TW-P1313301WW Amana Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Thomas from Tucson, AZ
- Parts Used:
- WP10111905
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Crushed ice bucket was damaged and needed to be replaced
I removed the damaged ice bucket and replaced the parts from the old one on to the new one. It was straight forward and not difficult
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Lemon Grove, CA
- Parts Used:
- WP67002052
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The wheel broke in half.
Remove ice tray from freeze. Removed all screws, replaced wheel. Reassembled unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Oakland, MD
- Parts Used:
- WPD7749401
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
broken end cap on ice icemaker bin
remove the tray from the freezer. unsnap the front cover from the bin. remove the four screws holding the metal helix and grinder assembly to the bin. slide the metal helix and grinder assembly out. slide the new end cap onto the end of the helix. (this is the only tricky part and takes some patience. The stub end of the helix has to slide into the hole in the end cap. You can't bend the helix, just work the end cap around until it slides over the helix end stub). Reassemble the grinder and helix to the bin, snap the cover on and slide back into the freezer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Shrewsbury, MA
- Parts Used:
- W11396033
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Broken light switch
Pried out the old switch and installed the new switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from Reynoldsburg, OH
- Parts Used:
- WPD7749401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ice Maker Auger Wouldn't Turn
I removed the ice tray and removed the front plastic cover that simply snapped off. I removed 4 hex screws with 1/4" nut driver. Then pulled the auger forward. This allowed me to slide the end cap into place. I put the auger in place and retightened the 4 hex screws, snapped on the plastic cover it worked fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Sandy, UT
- Parts Used:
- R0181181
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Replaced dorr closure cam on both doors of side-by-side
The fridge door was easy. Just unscrew top and lift off hindge. The freezer door took longer. But I had the user guide which helped. We unhooked the power harness at the top of the door, and disconnected the water line at the bottom of the door.
Frankly, it wasn't that hard for me because I had my son-in-law do it!
Frankly, it wasn't that hard for me because I had my son-in-law do it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Discovery Bay, CA
- Parts Used:
- WP2182124
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The ice stripper cracked from freezing.
There was three screws to remove to unmout the ice maker, and unplug the wire harness,then two to remove to slip in new stripper. All took about 20 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Lindenhurst, IL
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
icemaker
installed new parts
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- albert from El Paso, TX
- Parts Used:
- WPD7749401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
end cap broke under tlhe weight of ice and other frozen items that were ill placed
removed the ice maker tray and screws and that held the cover to the rotating mechanism that crushes and dispenses the ice. the end cap is then attached to the rotating mechanism and ice container, the cover is replaced;finishing the job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Edmond, OK
- Parts Used:
- R0181181
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
The right door was sagging and the handles were rubbing together
First, remove the plastic cover off the top hinge by removing the single phillips head screw.
Removed the three hex-head screws holding the hinge to the body of the fridge and then lift the hinge off of the door.
Lift the door off the bottom hinge and place on a flat surface so you can easily access the bottom.
Remove the single hex-head screw from the center of the door part of the closure cam and pull it free. Install the new part.
Next, remove the bottom portion of the closure cam from the lower door hinge (still attached to the fridge) by removing the single hex-head screw. Install the new part.
If needed, lube the lower door hinge with Vaseline and carefully set the door back on. (This is the hard part if you are working alone, as it can be hard to line up the hole.)
Lube the top hinge, reinstall, and replace the plastic cover. Easy as 1, 2, 3.
Removed the three hex-head screws holding the hinge to the body of the fridge and then lift the hinge off of the door.
Lift the door off the bottom hinge and place on a flat surface so you can easily access the bottom.
Remove the single hex-head screw from the center of the door part of the closure cam and pull it free. Install the new part.
Next, remove the bottom portion of the closure cam from the lower door hinge (still attached to the fridge) by removing the single hex-head screw. Install the new part.
If needed, lube the lower door hinge with Vaseline and carefully set the door back on. (This is the hard part if you are working alone, as it can be hard to line up the hole.)
Lube the top hinge, reinstall, and replace the plastic cover. Easy as 1, 2, 3.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Topsail Beach, NC
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken refrigerator compartment light switch.
The best part of the repair was how easy it was to find and order the part. Instead of searching the parts houses around town I just went to the PartSelect web site, quickly found and ordered the part in about five minutes, received the part the next day at my home and was ready to make the repair. Wow! What a pleasure for something to work the way it was meant to. Removed old switch located by prying out with sharp knife or screwdriver. Don't worry about breaking it or cracking plastic. Disconnect(unplug) wires from back of switch. Replace (plug-in) wires on back of new switch. Insert in location of old switch. Finisheed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WES from SPRINGVILLE, AL
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Switch Controlling Light When Door Open Was Briken
Poped ou the old switch, connected new switch and pushed back into socket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sally from San Antonio, TX
- Parts Used:
- 10783803
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Deli Drawer Sliding rails cracked.
Removed everything from above shelf. Removed entire assembly from fridge. (Easy, just clips into back) Then removed the rail assembly from the shelf and replaced with the new rails. Also had to remove the little roller wheels from the old assembly and put them on new rails. All this took less than 20 minutes to do, including taking out and replacing the food.
I am really glad you provide this service. I really like my "old" fridge and this was the only problem I have had in all the time I have owned it. Thanks for all your help and helpful diagrams.
Sally B. Tyger
San Antonio, TX
I am really glad you provide this service. I really like my "old" fridge and this was the only problem I have had in all the time I have owned it. Thanks for all your help and helpful diagrams.
Sally B. Tyger
San Antonio, TX
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from saint cloud, FL
- Parts Used:
- R0181181
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
door snapping when opening and closing
removed top hinge, lifted door off bottom hinge, replaced cam, installed door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from Stoughton, MA
- Parts Used:
- 12321807Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One side of the grill clip, broke
Just insert the new grill into the holes. Easy
Was this instruction helpful to you?
Thank you for voting!