SRD327S3L-P1307105WL Amana Refrigerator - Instructions

Had to remove the ice-maker (also easier than trying to work inside the freezer letting all the cold air out). A few mounting screws and an electrical connection in the back. After it was out you will need to remove the cover (not the superficial cover that just pries off) where the gear is behind it, just far enough so you can get the mounting tabs on the ice-stripper in. In order to to move this cover out, after removing the screws (the obvious), you'll need needle nose pliers to ever so slightly squeeze the plastic clips together that hold the plastic movable bracket and the metal ice level arm/switch, so it will pop out. Once you have room to put the ice stripper in, it should just all snap back together, then proceed in reverse to put it all back together.

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.

Replaced door closer part on hinge. Did not fix problem. Be sure to order mating bushing that goes in the bottom of the door . Part #67004977

Sorry for delay in writing. Part I ordered arrived two days ago and it was exactly what I needed. Knowing that there will be problems even with the smallest job I procrastinated starting. When I did start this morning I foud I had to completely remove the ice maker and disassemble it in order to install the water fill cup bracket. The challenge was reassembling the unit. Not hard for an experienced repairman but a challenge for layman. Everything is thing is back to gether now and power on cooling down the refrigerator. Won't know how successful it was until turn on water and ice is formed. If it works this saved $75 just to get a Sears repairman to come out and tell me what would be needed to fix the refrigerator and $1,000 if I had to buy a new refrigerator. Extremely satisfied with service I received. Thank you.

took the door off the hinges laided flat and withcordless drill and socket took the gasket off and replaced it with new one

remove right door replace lower door cam

followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00

empty frezzer take door off unplug wires going to ice maker unscrew/bolt icemaker replace door take motor cover off ice maker remove screws on motor replace ice cup and put every thing back together

Replaced cold water dispenser reservoir. Removed back access panel on bottom of refridgerator. Cut hoses using a wire cutter and removed old reservoir. Installed new unit (one screw). Routed hoses through bottom of refridgerator. Cut length to allow hose splicing just beneath resevoir. Connected hoses using hose splicers provided with the part. Musty taste is better if a couple glasses of water are run through the unit before drinking each time. Previously the water never got better. I think more hoses need to be replaced in the door to fully solve the problem. Repair took less than 30 minutes.

No instructions with part. Found a picture on line and changed the arm, but it didn't fix the problem. Fairly easy after figured out what needed to be done to get to the part.

Took ice maker out all together we removed 4 to 5 screws had to remove axel to get the broken piece out and new one in my husband said it was easy in and out in about 15 minutes saved about 150. 00 Thanks partslect

Grind rivet head off , install rivet tap end

There were 23 parts to be removed in order to replace part. So I printed out a diagram of the parts off the computer and the labled each part on the diagram with its name. I laid them all out in order and patiently re-assembled the ice maker. When finished, I gave a cheer!

After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.

I was very pleased with the entire experience. The part was easy to locate on the web site, it arrived very quickly and you sent a how-to video.