TZ22RE-P1157701WE Amana Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Guillermo from Brecksville, OH
- Parts Used:
- WP12550111Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Replace old door gasket
Star at the the right hand corner of door, loosen the screws, pull the old gasket out and at the same point push the new gasket,, tight all the screws
chek for any air leaks ...problem solved.
chek for any air leaks ...problem solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from Newnan, GA
- Parts Used:
- WP12550111Q
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Seal was balling up at bottom of doors and frig was not shutting
First placed the gasket in warm water so it would easily stretch over the door. Took off the inside front door cover and placed gasket on (magnet side out) then placed gasket on door and reattached. Works great and your prices and time of delivery were wonderful. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Duncan from Metairie, LA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The Switch Broke...Absolutely Fell Apart.
I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lori from Salem, NH
- Parts Used:
- WP10253524Q, WP10253523Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The refrigerator door cracked after 14 years
Unscrewed the old handles and replaced the new handles with the same screws... that easy! It was the easiest repair that I ever had to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert G from Waterford, WI
- Parts Used:
- WP12550109Q
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Door seal was damaged and did not seal properly
I first loosened all screws that are hidden by seal leading edge. I then removed seal. I made sure that I knew which side of seal was to be in contact with refrigerator door frame to provide the seal. I positioned the seal on the door inner panel starting at the top. After I had finished positioning the top I proceeded to position both sides and then the bottom. I tightened the screws only enough to hold the seal in position. After I had the seal in the proper position I tightened the screws that hold the seal in position. I used a hair dryer to heat seal and smooth out the the sealing edge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernie from Windsor, CA
- Parts Used:
- 833697
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
refrigerator not cooling properly
Replaced refrigerator cooling control. No luck. Replaced freezer cooling control. No luck. Coils were icing up. Unplugged frig and allowed coils to defrost. After more poking around, found that condenser fan was not spinning. Touch it and it'd start. That was definitely in need of replacement. Replacement was easy. Refrigerator is now running as it should.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Bethel Park, PA
- Parts Used:
- WP12550109Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Leaking Door Gasket
I removed all the screws except the top screws. These screws I loosed to make sure the door shelves remained in place. I did not want to remove the refrigerator door. I had read this method on PartSelect. It worked fine. I would recommend a power drill because of the number of screws supporting the door shelves; a power drill really help.
Please note there are only 3 sides of the "new" door gasket that are magnetized. It would have been nice to identify which are the magnetized sides before I did the installation; I guess I should have read the directions before hand.
It was an easy job.
Please note there are only 3 sides of the "new" door gasket that are magnetized. It would have been nice to identify which are the magnetized sides before I did the installation; I guess I should have read the directions before hand.
It was an easy job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Capac, MI
- Parts Used:
- M1205302, WP10450603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
broken roller
proped up frig, loosened screws, cut pin, installed rooler w/ new pin, rounded pin end, reistalled, lowered frig...everyone happy, thanks again partselect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Manchester Center, VT
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Refrigerator light would not stay on
Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.
reassembled the pieces.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paula from Swarthmore, PA
- Parts Used:
- WP10253523Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Crack In Top Of Handle
Took out three screws, kept the little plastic cover on the bottom screws and the screws--they did not come with the new handle. It took less than 5 minutes to do the whole job and while it was off I got to really clean my frig. Thanks for the quick delivery!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- walter from chrlestown, MA
- Parts Used:
- 10461901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
i lost the part and had to replace it
simpley place the support into slot provided.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Byron Center, MI
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light in my refrigerator didn't work.
At first I went to a local part supplier and they didn't have it in stock but could order it for me for $55.00 plus $10.00 to ship it. I told them I would have to think about it. I went home and got on the computer and found your web site and was I shocked when I saw the same part listed for $6.98 and $7.00 to ship it. You guys saved me $50.00. The part arrived in two day and took 5 min. to install. I now have light in my refrigerator. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Hamilton, OH
- Parts Used:
- 10417301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Being made of plastic , the slide rail had broke.
First I removed two screws holding the old slide rail in place. Then I pulled the old rail off and putt the new rail in place, then putt the two screws back in place.Then I took the drawer roller off the old rail and screwed in place on the new rail. Very easy !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from Malabar, FL
- Parts Used:
- WP10253523Q
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Refrigerator door handle was broken
First I removed the two screws that held the top of the handle in place. Then popped off the bottom holder. Replaced the broken handle with the new one, replaced the screws and snap on section and now have a nice looking refirigerator with a handle that works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Oak Creek, WI
- Parts Used:
- WP12550111Q
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Old gasket was leaking
Took door off, and put on saw horses. Loosen (don't remove) screws. Remove old gasket, put new one one, and tighten screws. Put door back on.
Was this instruction helpful to you?
Thank you for voting!