SRD528VE-P1320402WE Amana Refrigerator - Instructions

Had to push the light switch to get lamp to light up.
Removed power from refrig. and removed old light switch
and replaced with the one I got from Partselect. Turned power back on and was done.

1. Removed ice maker from frig.
2. Emptied all ice cubes.
3. Let it warm up to room temperature.
4. Removed front cover from bottom up (unsnapped).
5. Removed 4 screws.
6. Removed old helix cap.
7. Installed new helix cap.
8. Reverse of step 5 to step 1 above.

bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!

The fridge door was easy. Just unscrew top and lift off hindge. The freezer door took longer. But I had the user guide which helped. We unhooked the power harness at the top of the door, and disconnected the water line at the bottom of the door.

Frankly, it wasn't that hard for me because I had my son-in-law do it!

installed new parts

The best part of the repair was how easy it was to find and order the part. Instead of searching the parts houses around town I just went to the PartSelect web site, quickly found and ordered the part in about five minutes, received the part the next day at my home and was ready to make the repair. Wow! What a pleasure for something to work the way it was meant to. Removed old switch located by prying out with sharp knife or screwdriver. Don't worry about breaking it or cracking plastic. Disconnect(unplug) wires from back of switch. Replace (plug-in) wires on back of new switch. Insert in location of old switch. Finisheed.

First, remove the plastic cover off the top hinge by removing the single phillips head screw.

Removed the three hex-head screws holding the hinge to the body of the fridge and then lift the hinge off of the door.

Lift the door off the bottom hinge and place on a flat surface so you can easily access the bottom.

Remove the single hex-head screw from the center of the door part of the closure cam and pull it free. Install the new part.

Next, remove the bottom portion of the closure cam from the lower door hinge (still attached to the fridge) by removing the single hex-head screw. Install the new part.

If needed, lube the lower door hinge with Vaseline and carefully set the door back on. (This is the hard part if you are working alone, as it can be hard to line up the hole.)

Lube the top hinge, reinstall, and replace the plastic cover. Easy as 1, 2, 3.

removed the ice maker tray and screws and that held the cover to the rotating mechanism that crushes and dispenses the ice. the end cap is then attached to the rotating mechanism and ice container, the cover is replaced;finishing the job.

Removed everything from above shelf. Removed entire assembly from fridge. (Easy, just clips into back) Then removed the rail assembly from the shelf and replaced with the new rails. Also had to remove the little roller wheels from the old assembly and put them on new rails. All this took less than 20 minutes to do, including taking out and replacing the food.

I am really glad you provide this service. I really like my "old" fridge and this was the only problem I have had in all the time I have owned it. Thanks for all your help and helpful diagrams.

Sally B. Tyger
San Antonio, TX

After disconnecting the electricity. I followed the instructions as indicated in the "HOW TO" article on the website. I used a steel putty knife and pried the light switch out of its retaining hole. I worked the right side the most since this is the side with the retaining clip. After I removed the switch I transferred the two electrical outlets to the new switch and easily snapped it into place. Engaged the electric power and tested the switch.

I noticed that the refrigerator was having trouble maintaining temperature. Thought it might be time for new one until I found out that a new frig was $5k to $7K. Just happened to notice that the light switch didn't look quite right (was not sitting sqaure to the door). Once I pressed it it came loose. I then realized the the lights were staying on (50 watts of heating). Replaced the switch and the frig started working like new.

The worst part was unloading the door shelves. Removed upper hinge cover and hinge hex screws. This allows the door to be removed. Lay the door on side. Remove screw that holds cam in place. Replace
broken cam with new piece. Put the door back on the hinge pin and replace upper hinge screws and cover.
Now reload all of the stuff.

Pried out ice blade bar and removed broken water fill cup and replaced with new one.The whole repair costs $9.52 So I saved $ 190 over the cost of Appliance man visit!
It would have been $150& $50 for visit to replace ice maker unit.

Remove the grandkids pictures from the door then empty the contents inside the door. Remove the top hinge cover and the top hinge bracket. Lift the door off the bottom pivot. Replace the lower cam by removing one screw. With the door in the horizontal position, remove and replace the upper cam. Apply a little grease on both cam surfaces. Align the door before tightening the top bracket and your done. If you did not take a picture of the door before you started the project you will have to rely on memory to arrange the pictures in the proper location.

Removed the top hinge (4 screws)-lifted the door off of the lower hinge-replaced both halves of the cam kit and mounted the door and reattached the upper hinge.
Probably took about fifteen minutes total.