SRD520SE-P1186301WE Amana Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- michael from pleasant grove, UT
- Parts Used:
- WP67002052
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
crushed ice wheel broken
very easy, with use of screwdriver and 1/4 in nut driver. just remember the way the blades go and get them back the same way. had it fixed in 15 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from GROVESPRING, MO
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
light did not work on the refrigerator side
bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesse from Slidell, LA
- Parts Used:
- WPD7749401
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
not distributing ice
1. Removed ice maker from frig.
2. Emptied all ice cubes.
3. Let it warm up to room temperature.
4. Removed front cover from bottom up (unsnapped).
5. Removed 4 screws.
6. Removed old helix cap.
7. Installed new helix cap.
8. Reverse of step 5 to step 1 above.
2. Emptied all ice cubes.
3. Let it warm up to room temperature.
4. Removed front cover from bottom up (unsnapped).
5. Removed 4 screws.
6. Removed old helix cap.
7. Installed new helix cap.
8. Reverse of step 5 to step 1 above.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from LaPlace, LA
- Parts Used:
- WPD7749401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice Maker Auger Jambed and Broke Helix
Removed 6 screws total and removed the entire Auger and Ice Crusher. The broken Helix just fell off, I put the new one on after a little finagaling to get it lined up right and it just snap into place. Replace the screws, put the bucket back, dumped in the Ice and the dispenser started working Fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BJ from Hanover, PA
- Parts Used:
- 12321807Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Kick plate had a broken clip and would not stay on refrigerator
It was simple. Screwed clips on kick plate. That was it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from Southlake, TX
- Parts Used:
- 12321807Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
kick plate wouldn't stay on
i inserted the connectors to the kickplate and put it on the refrigerator. very easy...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Edmond, OK
- Parts Used:
- R0181181
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
The right door was sagging and the handles were rubbing together
First, remove the plastic cover off the top hinge by removing the single phillips head screw.
Removed the three hex-head screws holding the hinge to the body of the fridge and then lift the hinge off of the door.
Lift the door off the bottom hinge and place on a flat surface so you can easily access the bottom.
Remove the single hex-head screw from the center of the door part of the closure cam and pull it free. Install the new part.
Next, remove the bottom portion of the closure cam from the lower door hinge (still attached to the fridge) by removing the single hex-head screw. Install the new part.
If needed, lube the lower door hinge with Vaseline and carefully set the door back on. (This is the hard part if you are working alone, as it can be hard to line up the hole.)
Lube the top hinge, reinstall, and replace the plastic cover. Easy as 1, 2, 3.
Removed the three hex-head screws holding the hinge to the body of the fridge and then lift the hinge off of the door.
Lift the door off the bottom hinge and place on a flat surface so you can easily access the bottom.
Remove the single hex-head screw from the center of the door part of the closure cam and pull it free. Install the new part.
Next, remove the bottom portion of the closure cam from the lower door hinge (still attached to the fridge) by removing the single hex-head screw. Install the new part.
If needed, lube the lower door hinge with Vaseline and carefully set the door back on. (This is the hard part if you are working alone, as it can be hard to line up the hole.)
Lube the top hinge, reinstall, and replace the plastic cover. Easy as 1, 2, 3.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- albert from El Paso, TX
- Parts Used:
- WPD7749401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
end cap broke under tlhe weight of ice and other frozen items that were ill placed
removed the ice maker tray and screws and that held the cover to the rotating mechanism that crushes and dispenses the ice. the end cap is then attached to the rotating mechanism and ice container, the cover is replaced;finishing the job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JONATHAN from ELKINS PARK, PA
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
old switch left freezer bulb always-on
Unplug appliance. Socket wrench to unscrew two screws. Module drops down. disconnected two press-on wires by prying off with screwdriver. Removed old switch. Press-fit new switch. Reconnected two wires (color coded). Screwed module back in place. Plug in appliance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from middle island, NY
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light would work intermitently
removed the 2 screws that held the panel in place, had to reach up and push on locking tabs to lower trhe front of the panel. was able to then push on the locking tab of the switch to release it. removed the wires, replaced them onto the new switch, and snapped the switch into place. the rest was reverse of the uninstall process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carlos from haverstraw, NY
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Replace Bad Switch
Pry old switch and pull out. Disconect two wires. Put two wires on new switch, must be inserted right and connections not loose. Put switch in, making shure wies do not come off and snap in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Jefferson Hills, PA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Internal light did not come on each time the door was opened.
After disconnecting the electricity. I followed the instructions as indicated in the "HOW TO" article on the website. I used a steel putty knife and pried the light switch out of its retaining hole. I worked the right side the most since this is the side with the retaining clip. After I removed the switch I transferred the two electrical outlets to the new switch and easily snapped it into place. Engaged the electric power and tested the switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Jenkintown, PA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lights didn't always come on when was opened
Used a screwdriver to pry loose the old switch, swapped wires to the new switch and pushed it into the opening. Took about 2 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Watertown, NY
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
19 year old light switch broke
Great service. Unpluged old switch and pluged in new one. Works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from Palmetto, FL
- Parts Used:
- 12321807Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Fridge had large gap between bottom of the doors and the floor
Put the clips on the grille plate and pushed it on. The fridge looks new again
Was this instruction helpful to you?
Thank you for voting!