SRD520TW-P1308801WW Amana Refrigerator - Instructions

Removed the top hinge (4 screws)-lifted the door off of the lower hinge-replaced both halves of the cam kit and mounted the door and reattached the upper hinge.
Probably took about fifteen minutes total.

I followed the other web notes with one change .Since I too forgot the lube , I used a pry bar and block of wood to lift the door and a tooth pick to glob some lube in the lower hinge.

Took the door off, and replaced the plastic shim on the bottom that was the cause of the problem. The shim had broken into pieces and was no longer holding the door in height and alignment. I was proud of myself that I could repair it myself and avoid a $125.00 service call from a repairman. Total cost of repair including shipping and handling was just south of $12.00.

I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.

Took a toital of 15 minutes to exchange the bucket. A total of 4 screws to remove the auger and front of the bucket. Anyone can do this repair!!

My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!

Sincerely, Ron Marshall, Billings, MT

Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!

I received my part in two days. Installation was easy. Most difficult part was attaching the inclosed metal clips onto the grill. The entire process took me 10 minutes. That included cleaning under the refridgerator. My wife said it was dusty.

The repair went excellent! The part search was easy and shipped and delivered very quick!

Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.

Had to remove the ice-maker (also easier than trying to work inside the freezer letting all the cold air out). A few mounting screws and an electrical connection in the back. After it was out you will need to remove the cover (not the superficial cover that just pries off) where the gear is behind it, just far enough so you can get the mounting tabs on the ice-stripper in. In order to to move this cover out, after removing the screws (the obvious), you'll need needle nose pliers to ever so slightly squeeze the plastic clips together that hold the plastic movable bracket and the metal ice level arm/switch, so it will pop out. Once you have room to put the ice stripper in, it should just all snap back together, then proceed in reverse to put it all back together.

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.

remove right door replace lower door cam

There were 23 parts to be removed in order to replace part. So I printed out a diagram of the parts off the computer and the labled each part on the diagram with its name. I laid them all out in order and patiently re-assembled the ice maker. When finished, I gave a cheer!

Replaced door closer part on hinge. Did not fix problem. Be sure to order mating bushing that goes in the bottom of the door . Part #67004977