TX22S3L-P1196002WL Amana Refrigerator - Instructions

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

just cleaned it and put in place. I was really impressed as to how fast it was sent to me. I broke it on Nov. 1 and placed the order that afternoon and received the new glass on Saturday Nov. 3. I really appreciated that as I never expected it until the following week. Thank you for the fast service!

Remove 3 screws, took top hinge out, fz door and inserted shim...done.

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

First I removed the old handle by removing the 3 screws holding it in place. There are 2 on the top and 1 at the side of the door. When I began to put the new handle on it became apparent that the metal frame inside the handle was not aligned perfectly with the old screw holes. The plastic is not even with the door horizontally on the top, but it fits otherwise. Be careful not to over tighten the screws when installing. Pretty easy overall.

removed 3 phillips jead screws. removed old hangle. cleaned around the site of old grime./ smile. positioned new handle, applied the 3 screws, tightened, and " whalah" like new.

Removed a small cover plug on the lower portion of the handle, removed three screws. Took off old handle, positioned the new one, replaced the screws and cover plug and that was it! Wouldn't have taken even 15 minutes if I hadn't dropped a screw and had to search for it - lol.

Installed missing spacer

Removed old handle. Cleaned area. Installed new handle. Remember to save small cover at bottom of old handle.

I got the product very quickly. (thank you) Looked at online instructions that were quite vague. Pulled plug.Removed the holder for the fan motor slid it out to see what I had. Removed the mounting screws (3) and slid the motor an fan blade out. I made a cut between the wires and marked the "top" wire to motor to be sure to spin in right direction. Removing fan blade hold down clamp was NOT explained at all but I noted that the shaft on the motor was threaded, so I used pliars and held the shaft white un-screwing clamp. I cleaned the fan blades with degreaser and scraped edges of opening on holder opening. Make sure to use ALL the NEW parts included with this kit when re-installing. They send them for a reason. When slpicing and connecting wires it is a 50/50 shot if you don't mark before cutting. You can connect and try plugging fridge back for moment and make sure it is blowing OUT. Put everything back together and after turning DOWN the thermostats twice, fridge is back to usual. Ice maker is cranking out ice and outside case is cool to the touch.

Note: This can be a DIRTY job especially with 4 dogs in house. Fir and grease don't mix well

It was not difficult it took a lot of time to remove the panel by removing like 20 bolts around it. Put the panel down on the floor face down then wrap the gasket around it. Putting back the panel on the door you can use some help to hold it up, while you are screwing back all those bolts. After screwing the upper bolts of the panel, you better go down at the bottom and start working on it, because the gasket tends to fall off at the bottom part. Then you can screw all the rest of the bolts. That's how you do it.

First removed door, then removed all screws, then removed inside door panel, then removed old gasket, then installed new gasket, then reattached inside door panel and all screws, then reattached door, then used hair dryer to get gasket to seal in several areas.

First I removed all the screws from the back cover.
2nd removed fan nut and fan blade
3rd removed fan bracket
4th I traced wire to the condenser and disconnected wires from wire nuts.
Installed existing fan brackets to new motor kit
then reconnected wire nuts to new motor cord
Reinstalled fan nut and blade,
reinstalled cover, plugged it in and BAM .WORKS PERF!

figured out the condenser fan was kaput. Tried WD, worked for several days then gave out completely. Took off back of fridge and trained small fan on compressor while I ordered new condenser fan. The swap was easy, undid the housing bolts, stripped off the connector, reconnected and voila! works perfect.