Models > TX18QL-P1111401WL > Instructions

TX18QL-P1111401WL Amana Refrigerator - Instructions

Jump to:

All Instructions for the TX18QL-P1111401WL
91 - 105 of 270
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Walter from Green Valley, AZ
Parts Used:
WP10253524Q
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The plastic cover on the old hadle broke off.
It was very simple. Pulled the little cover off of the bottom screw and removed it along with the 2 top screws. Then just do the reverse to install the new handle.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from Colorado Springs, CO
Parts Used:
WPW10662129
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
freezer and refrigerator compartments not cold enough
Used the suggested problem list here to narrow down that the repair was most likely the run capacitor. Poped the new one in and I now have better control of my compartment ranges. I have a temperature gauge in each compartment. Check them every opening of the doors.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jacqueline from LEXINGTON PK, MD
Parts Used:
WPW10662129
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers
No cold
Like you video
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Adam from GLOVERSVILLE, NY
Parts Used:
WPW10662129
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Plugged it in.
Not so good that was not the problem. Fan is not seized and all the lights work and display is not on but lights up as well. No start once plugged back in after 15 minutes of being unplugged. Nothing same no change.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jill from FALL RIVER, MA
Parts Used:
D7520510
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
The clips broke off our old one , I glued to many times
Opened new kickplate from pkg and snapped it on !! So happy
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Barbara from Shelton, CT
Parts Used:
D7520514
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
grille toe plate broken
I removed the old grille toe plate and snapped the new one in it's place.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Debbie from Salisbury, MO
Parts Used:
WP10253523Q
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Broken handle
After popping off the lower cover all I needed was a screwdriver to remove both the upper 2 screws and the lower screw. The new handle was attached in seconds and it matches great.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Murray from Medford, NJ
Parts Used:
10253510Q
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Original door handle was broke at the top.
Removed 2 screws from top and removed bottom cap cover to access the bottom two screws for its removal. Replaced handle by using the same screws and put back the small plastic cap cover and DONE.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gregory from Wildomar, CA
Parts Used:
10253510Q
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Top of door handle cracked
Removed old handle with a total of three screws, two on top and one on bottom of handle. Replaced with new handle and put existing screws back in place. Very easy!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mr & Mrs Robert G from San Marino, CA
Parts Used:
10253510Q
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Pieces of plastic had broken off the door handle
Replacement was extraordinarily easy. It took about 5 minutes, including the time to find my tools and put them away after I was done. As others have warned, only the handle itself was shipped. The trickiest part was being careful not to break the little plastic cover at the bottom of the handle when I pried it off. Apparently a screwdriver under any edge would have worked okay. There were three Phillips-head screws (replacements were not included in the package!) - and that was it.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from HELENDALE, CA
Parts Used:
WPW10662129
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
freezer would not freeze
inst said,"50 pct of the time this calls for new capacitor," so we changed the capacitor. Same prob. It also said,"25 pct of the time it's the bi-metal thermostat" So we ordered it. We removed the plastic rear panel from inside the freezer comp. using small nut driver. Here we found much ICE surrounding the defrost unit, three inches thick. We thawed the whole mess. and the freezer has worked fine ever since. I think my habit of getting ice cubes from the inside container rather than from the ice cube dispenser, had kep t the freezer door open too much, interfering with the normal defrost cycle and allowing ice to build up over time so that it finally defeated the system. My new rule, "get ice cubes only from the front."
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from WILMINGTON, OH
Parts Used:
WPD7605106Q
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
The old seal was broken and leaking causing the freezer to ice up.
The repair was straight forward and was not hard. You do almost need 3 hands as the reinstallation of the inner door panel can be awkward. The only issue that I have is that the new seal has a poor fit. While it was received folded over on itself, this was not the problem. The seal does not expand enough on one side to fully seal the door. It also has a very weak magnet. If the magnet was stronger, then maybe it would seal better. It does still leak to some extent. The seal that was removed had a stronger magnet that the new one does. I would include a photo, but this system does not allow me to add attachments. Overall, I'm pleased with the time that it took to get the gasket, and the ease of replacement, but am not satisfied with the quality of the sealing or the strength of the magnet that holds the door closed. I would rate replace as 8 out of 10, and part quality and how it works as a 2 on a scale of 10.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Douglas from Mesa, AZ
Parts Used:
833697
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers
Condenser fan motor froze up
Unplug fridge, unpluged fan motor from plug socket, removed bracket screws, removed fan retainer clip from shaft. removed screws holding fan to bracket
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Marion from Winfield, IL
Parts Used:
10253510Q
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Tightening the screws on the top of the handle cracked the plastic around them
I used a phillips screw driver to remove the screws. The toughest part was removing the lower screw cover so that it could be reused. Piece of cake!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from Cherokee Village, AR
Parts Used:
WP10442411
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
freezer would not defrost
remove ice maker vent and back piece. Unclip defrost thermostat and unplug. Plug new thermostat in and clip to element, reattach back piece, vent and ice maker. Is a tight fit getting icemaker out, there are 3 screws 2 on top and one on bottom.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the TX18QL-P1111401WL
91 - 105 of 270