TK21R3L-P1189001WL Amana Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Martin from Alsip, IL
- Parts Used:
- WP12550111Q
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
gasket was ripped and hanging off of door
I unscrewed about 32 screws with a nutdriver,removed door shelving while leaving door attached to fridge.Replaced old gasket with new one,used a hair dryer to get wrinkles out from shipping.Installed onto door,fit perfectly!.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from HELENDALE, CA
- Parts Used:
- WPW10662129
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
freezer would not freeze
inst said,"50 pct of the time this calls for new capacitor," so we changed the capacitor. Same prob. It also said,"25 pct of the time it's the bi-metal thermostat" So we ordered it. We removed the plastic rear panel from inside the freezer comp. using small nut driver. Here we found much ICE surrounding the defrost unit, three inches thick. We thawed the whole mess. and the freezer has worked fine ever since. I think my habit of getting ice cubes from the inside container rather than from the ice cube dispenser, had kep t the freezer door open too much, interfering with the normal defrost cycle and allowing ice to build up over time so that it finally defeated the system. My new rule, "get ice cubes only from the front."
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mona L from CALDWELL, ID
- Parts Used:
- WP12550112Q, WP12550111Q
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
Not really a problem!
My brother just didn't listen and was doing it the hard way until a friend of mine looked it up on U-Tube and then it went pretty smooth. Lol So my advice is to look it up on U-Tube before you begin!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Lowell, MI
- Parts Used:
- 833697
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Socket set
original motor stopped
removed old and instaslled new. biggest problem was getting to one of the screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Belhaven, NC
- Parts Used:
- 833697
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
cooling fan quit
Ordered new fan motor on line took out old motor and replaced with new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- STEVE from AUSTIN, TX
- Parts Used:
- 10461901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
support post broken
removed crisper drawers, then food items from shelf above, then replaced support post and replaced drawers and food items from shelf
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from whitwell, TN
- Parts Used:
- 833697
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench set
fan motor had gone bad
I removed the nuts that held the motor mount, then removed fan blade, cut the wires, and slid the motor pass the mounts and the coil shroud, Installed motor in reverse order. worked out ok.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Milford, MA
- Parts Used:
- 833697
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
freezer and food section too warm
removed lower back cover. diconnected fan ass'y electrical connection, removed fan housing (3 screws). removed fan motor from housing. cut old connector from fan and installed on new fan with wire nuts included. re-installed new fan to housing and re-installed housing to frame.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Al from Tonka Bay, MN
- Parts Used:
- 833697
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Condenser Fan Failure
Partition between Freezer and Fridge was running very hot. (Warm is normal). Oiling fan did not work. The only problems encountered in the replacement were getting fan out and in through coolant lines, cut plug off to accomodate generic fan wiring, getting the screws back in without cooking your hand on a hot compressor. Unit works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clinton from Metairie, LA
- Parts Used:
- WP10253523Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Handle
Removed the plastic cover cap on side screw the removed the three screws, removing the old handle. Cleaned screws and mounting area on door, then installed the new handle. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Palmdale, CA
- Parts Used:
- 10461901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The post broke in two places, no longer holding up drawers and glass shelf
I simply put the post in and set up the drawers and shelf.
Was this instruction helpful to you?
Thank you for voting!
Light wouldn't always come on when door was opened.
Removed the 6 screws that held the panel up, pulled the panel down. Removed the wires on the old switch. Pulled out the old switch, and pushed the new one back in place. Attached the 2 wires, pushed panel back into place and installed the 6 screws. Pluged back in and light works every time the door is opened now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Lovettsville, VA
- Parts Used:
- WP10253524Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The old door handle had cracked and was about to snap off the door.
I removed the old door handle with a screwdriver and simply replaced it with the new door handle. I put the "Amana" name plate from the old door handle into the new one. Took less than 15 minutes. Very, very pleased. Plus the ivory color matches pretty well with a refrigerator that is more than 15 years "young". :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darleene from Beaverton, MI
- Parts Used:
- 10461901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The plastic part just got old and crumbeled..so it wouldn't fit.
First I couldn't get it back..due to eye problems so i gave it to my husband and he just did it in a flash..you set it under the glass and put the drawers or crispers back in and its done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David Barnes from ROSWELL, NM
- Parts Used:
- W11384469
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rocker on switch broke off
Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.
Was this instruction helpful to you?
Thank you for voting!