TM18V2W-P1318006WW Amana Refrigerator - Instructions

I first removed the icemaker pump and filler tube fron the back of the refrigerator by using an adjustable wrench and pliers. (very simple connection) I went ahead and replaced both items at that time.

Next I opened the bottom freezer and removed the top wire tray and ice container. I removed the bottom nut from the ice maker, pulled the electrical plug lose from the freezer connection. I then just lifted the ice maker upward and off the two screws on the side wall and out it came!

I had a little trouble with the filler tube as it came into the freezer. I had to go back and forth to the back of the refrigerator and freezer a couple of times adjusting the tube, so it woiuld clear the inside freezer wall.

This was a very minor problem. I feel like if I had followed the instructions and made sure the tube came through before attaching the icemaker it would have worked like a charm!

What I really liked, was everything was in the box for the job.

Pull refrigerator out from wall to shut off water and power. Remove ice bin, pulling front down then out. Remove screw at bottom of icemaker, then pull down to release two clips, Pull out a couple inches to get hand behind icemaker to release wiring harness connector. (squeeze top and bottom to release clips). Remove unit. Remove wiring harness and wire bail from old unit and install on new unit. Reverse steps to install new unit. Make sure ice bin is fully inserted, or unit will not function.

i just took the prts apart and replaced with new part really easy and saved $185.00 easy as pie

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

Despite a long delay due to a lack of stock on hand, the correct part arrived and matched in color. It came without the little rectangular plastic cap or cover for the bottom bolt, so it was good to have kept the old handle and plastic cap on hand. I imagine other owners might have thrown out a broken part, bolts and cap in the meantime. Strictly the handle arrived, but it was easy to install. I'm grateful for a part I wasn't sure could be found.

After checking the water valves ordered new ice maker. received the part three days after ordering! Clearing out food, removing the old one and installing the new unit took under 15 minutes. Everything went fine.

New seal arrived basically folded in half for shipping. Was advised to use hair dryer and/or hot water to restore original shape. Neither worked. I installed it anyway and am waiting (3 days so far) for it to seal (so far, no luck). I'll give it another day or 2, re-install the old one and write off the $75

remove parts that were not need installed water valve , ice maker unit and hooked up water supply tested and it works fine. got the parts really quick Thank You

Part received was what I needed. There was one issue--the 'feed' opening to receive water and direct it into the ice tray was a side feed and what I needed was a back feed. That means I had to do some exchanging of parts to make it work. That exercise took more time that the actual installation.

Removed the old. Took off the name plate from the old handle. Put the name plate on the new. Installed new handle.

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Very simple fix, remove 3 screws, two connectors to the old switch

Remove 3 screws, took top hinge out, fz door and inserted shim...done.