TH21S3L-P1195604WL Amana Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Stephen from Lovettsville, VA
- Parts Used:
- WP10253524Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The old door handle had cracked and was about to snap off the door.
I removed the old door handle with a screwdriver and simply replaced it with the new door handle. I put the "Amana" name plate from the old door handle into the new one. Took less than 15 minutes. Very, very pleased. Plus the ivory color matches pretty well with a refrigerator that is more than 15 years "young". :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darleene from Beaverton, MI
- Parts Used:
- 10461901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The plastic part just got old and crumbeled..so it wouldn't fit.
First I couldn't get it back..due to eye problems so i gave it to my husband and he just did it in a flash..you set it under the glass and put the drawers or crispers back in and its done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clinton from Metairie, LA
- Parts Used:
- WP10253523Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Handle
Removed the plastic cover cap on side screw the removed the three screws, removing the old handle. Cleaned screws and mounting area on door, then installed the new handle. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Palmdale, CA
- Parts Used:
- 10461901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The post broke in two places, no longer holding up drawers and glass shelf
I simply put the post in and set up the drawers and shelf.
Was this instruction helpful to you?
Thank you for voting!
Light wouldn't always come on when door was opened.
Removed the 6 screws that held the panel up, pulled the panel down. Removed the wires on the old switch. Pulled out the old switch, and pushed the new one back in place. Attached the 2 wires, pushed panel back into place and installed the 6 screws. Pluged back in and light works every time the door is opened now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Wheeling, IL
- Parts Used:
- WP10253524Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Refrigerator door handle was splitting at the curve.
I removed the old handle and replaced it with the new one. Three screws and I was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Mission Viejo, CA
- Parts Used:
- WP10253524Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
we had a broken door handle that looked very unsightly
The repair was very simple and the refrigerator now looks almost new. We are very pleased with your service and the fast delivery time. We give it 5 stars.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Lakeland, FL
- Parts Used:
- 10461901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken support post for crisper drawer
Lifted both drawer runners removed the broken post, put new post in place. Job completed in lest than two min.
Was this instruction helpful to you?
Thank you for voting!
Broken Framing for Crisper Drawer
Very easy to do -- removed a screw - pulled the broken center rail away and replaced with new one -- realigned the humidity control band - installed the new roller on the rail -- reassembled the unit and done!
Note to those ordering new rollers. The mounting screw for the roller is not in the bag -- apparently it's ordered separately -- very strange -- seems like they should come together.
Note to those ordering new rollers. The mounting screw for the roller is not in the bag -- apparently it's ordered separately -- very strange -- seems like they should come together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Elburn, IL
- Parts Used:
- 10476101Q
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broken front roller
I removed two screws holding the assembly. removed the assembly then toke the roller and bracket out of the houseing and replaced with new part. reverse the procedure for installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeremy from State College, PA
- Parts Used:
- 833697
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Refrigerator would not stay cold
Removed rear cover to see non-operating fan - removed three mounting screws on the motor that were a challenge to access. Swapped fan from old motor onto new motor - one threaded nut on the motor shaft. Spliced new fan wires into fan wires of the wiring harness and mounted with three self-tapping screws supplied with new fan motor. Replaced rear cover and plugged it in! Now the refrigerator cools like new (1981 model side-by-side Admiral)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Linthicum, MD
- Parts Used:
- R0151005
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Frig wasn't as cold as it should be; even with gauges cranked all the way down
Noticed fan wasn't running, remo ved, verified that it wasn't a sensor, ordered new part, installed new part...works like new. Everything is cold again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Howell, MI
- Parts Used:
- 833697
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
The door gasket was very hot which is caused by an overheated expansion line that runs along the area of the door gasket. This was caused by a failed cooling fan motor.
Pulled out the refrigerator and removed the two panels from the rear of the refrigerator. Removed the fan held in by four screws and unplugged the connector. Soldered on the original connector, installed the fan to the motor and re-installed the unit into the refrigerator. Then blew out and vaccumed the condenser coils.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ivanka from Atlantra, GA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
burned oven bulb
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.
Was this instruction helpful to you?
Thank you for voting!
Did not work light does not come on when the door opens. Would try the light socket. It not sure how good the switch got plugged in.
By watching a video.
Was this instruction helpful to you?
Thank you for voting!