TR25S5-P1196401WE Amana Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David Barnes from ROSWELL, NM
- Parts Used:
- W11384469
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rocker on switch broke off
Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from TEMECULA, CA
- Parts Used:
- W11384469
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Light switch broke off
We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from COVINGTON, LA
- Parts Used:
- 833697
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
refrigerator stopped cooling due to condenser over-heating
Pull refrigerator out to access back, unplug unit and remove the 3 .25" screws cut the power leads to motor and install new with easy to understand instructions provided with new motor. Plug refrigerator back in and enjoy your cold beverages once more. EASIEST REPAIR EVER.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- STEVE from AUSTIN, TX
- Parts Used:
- 10461901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
support post broken
removed crisper drawers, then food items from shelf above, then replaced support post and replaced drawers and food items from shelf
Was this instruction helpful to you?
Thank you for voting!
Light wouldn't always come on when door was opened.
Removed the 6 screws that held the panel up, pulled the panel down. Removed the wires on the old switch. Pulled out the old switch, and pushed the new one back in place. Attached the 2 wires, pushed panel back into place and installed the 6 screws. Pluged back in and light works every time the door is opened now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from GROVESPRING, MO
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
light did not work on the refrigerator side
bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Palmdale, CA
- Parts Used:
- 10461901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The post broke in two places, no longer holding up drawers and glass shelf
I simply put the post in and set up the drawers and shelf.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lois from Northfield, IL
- Parts Used:
- WP10609807
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
shelf was broken
The part came quickly and slid right in - no tools needed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Lakeland, FL
- Parts Used:
- 10461901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken support post for crisper drawer
Lifted both drawer runners removed the broken post, put new post in place. Job completed in lest than two min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Elburn, IL
- Parts Used:
- 10476101Q
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broken front roller
I removed two screws holding the assembly. removed the assembly then toke the roller and bracket out of the houseing and replaced with new part. reverse the procedure for installation.
Was this instruction helpful to you?
Thank you for voting!
Broken Framing for Crisper Drawer
Very easy to do -- removed a screw - pulled the broken center rail away and replaced with new one -- realigned the humidity control band - installed the new roller on the rail -- reassembled the unit and done!
Note to those ordering new rollers. The mounting screw for the roller is not in the bag -- apparently it's ordered separately -- very strange -- seems like they should come together.
Note to those ordering new rollers. The mounting screw for the roller is not in the bag -- apparently it's ordered separately -- very strange -- seems like they should come together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Howell, MI
- Parts Used:
- 833697
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
The door gasket was very hot which is caused by an overheated expansion line that runs along the area of the door gasket. This was caused by a failed cooling fan motor.
Pulled out the refrigerator and removed the two panels from the rear of the refrigerator. Removed the fan held in by four screws and unplugged the connector. Soldered on the original connector, installed the fan to the motor and re-installed the unit into the refrigerator. Then blew out and vaccumed the condenser coils.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeremy from State College, PA
- Parts Used:
- 833697
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Refrigerator would not stay cold
Removed rear cover to see non-operating fan - removed three mounting screws on the motor that were a challenge to access. Swapped fan from old motor onto new motor - one threaded nut on the motor shaft. Spliced new fan wires into fan wires of the wiring harness and mounted with three self-tapping screws supplied with new fan motor. Replaced rear cover and plugged it in! Now the refrigerator cools like new (1981 model side-by-side Admiral)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ivanka from Atlantra, GA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
burned oven bulb
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.
Was this instruction helpful to you?
Thank you for voting!
Did not work light does not come on when the door opens. Would try the light socket. It not sure how good the switch got plugged in.
By watching a video.
Was this instruction helpful to you?
Thank you for voting!