SRD325S5E-P1307203WE Amana Refrigerator - Instructions

Part was easy to order, delivered quickly, installation very easy. Just unplug the unit, pop out the old swich using a screwdriver, disconnect and reconnect leads and pop switch back in. Definitely recommend that you can do it too.

Pry old switch and pull out. Disconect two wires. Put two wires on new switch, must be inserted right and connections not loose. Put switch in, making shure wies do not come off and snap in place

Unplug appliance. Socket wrench to unscrew two screws. Module drops down. disconnected two press-on wires by prying off with screwdriver. Removed old switch. Press-fit new switch. Reconnected two wires (color coded). Screwed module back in place. Plug in appliance.

Removed everything from above shelf. Removed entire assembly from fridge. (Easy, just clips into back) Then removed the rail assembly from the shelf and replaced with the new rails. Also had to remove the little roller wheels from the old assembly and put them on new rails. All this took less than 20 minutes to do, including taking out and replacing the food.

I am really glad you provide this service. I really like my "old" fridge and this was the only problem I have had in all the time I have owned it. Thanks for all your help and helpful diagrams.

Sally B. Tyger
San Antonio, TX

I noticed that the refrigerator was having trouble maintaining temperature. Thought it might be time for new one until I found out that a new frig was $5k to $7K. Just happened to notice that the light switch didn't look quite right (was not sitting sqaure to the door). Once I pressed it it came loose. I then realized the the lights were staying on (50 watts of heating). Replaced the switch and the frig started working like new.

removed top hinge, lifted door off bottom hinge, replaced cam, installed door.

After disconnecting the electricity. I followed the instructions as indicated in the "HOW TO" article on the website. I used a steel putty knife and pried the light switch out of its retaining hole. I worked the right side the most since this is the side with the retaining clip. After I removed the switch I transferred the two electrical outlets to the new switch and easily snapped it into place. Engaged the electric power and tested the switch.

disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.

I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.

Took a toital of 15 minutes to exchange the bucket. A total of 4 screws to remove the auger and front of the bucket. Anyone can do this repair!!

Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!

My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!

Sincerely, Ron Marshall, Billings, MT

Took off the good old parts and screwed them onto the new draw. It was easy. teh best part was the draw came really fast in the mail. Fed Ex and it did not cost us an arm and a leg to buy it.

The repair went excellent! The part search was easy and shipped and delivered very quick!

Had to remove the ice-maker (also easier than trying to work inside the freezer letting all the cold air out). A few mounting screws and an electrical connection in the back. After it was out you will need to remove the cover (not the superficial cover that just pries off) where the gear is behind it, just far enough so you can get the mounting tabs on the ice-stripper in. In order to to move this cover out, after removing the screws (the obvious), you'll need needle nose pliers to ever so slightly squeeze the plastic clips together that hold the plastic movable bracket and the metal ice level arm/switch, so it will pop out. Once you have room to put the ice stripper in, it should just all snap back together, then proceed in reverse to put it all back together.