AC2228HEKW0 Amana Refrigerator - Instructions

The instructions in the package were not helpful. They wanted me to cut the wiring harness and described where to cut based on the wire colors. My wires were not the same color! I removed the light mechanism using a combination of a screwdriver, putty knife, and plain old muscle with my fingers! The wiring harness unplugged easily and the new one inserted. It was easy to push the whole assembly back into the door. I spent more time looking for something to cut the wiring harness with (and never did find it) than the whole job actually took without needing to cut anything!

Popped out the old light switch with a butter knife from the bottom first, disconnected the plug in. Install was just the reverse. Super easy fix

Removed the top hinge cover with Philips screwdriver. Removed the three bolts holding the top hinge in place. Removed the top hinge, and lifted the door off the remains of the lower hinge. Unbolted the remnants of the lower hinge closure mechanism and replaced it with the new set. Reassembled the door on the lower hinge, and then replaced and bolted back on the top hinge. Door back to full working order in less than fifteen minutes.

dismanteled ice bucket end and removed auger slid helix off and reinstalled auger in bucket. real good instructions.

I did not do the repair yet, there is no schematic on how to route the hose; also no description of how to do the routing/connections.

I had to pull the old ice bucket out, remove the front cover and the ice churner from the old bucket. The churner had to be installed onto the new ice bucket, then the front cover had to be snapped back on to the front of the ice bucket. Finally, the new bucket was slid into place. The whole process was relatively easy for a non-mechanical person like me, with the help of detailed instructions that came with the unit. The on-line video was also helpful. I would recommend this company to friends.

I removed the ice tray from the freeze. Turn over and remove screws holding the face plate on. Remove the 4 screws holding the crushing mechanism in place. Pull the entire mechanism out and remove the nut holding the blades together. Remember the alignment of the blades. Remove blades and then the pastic crush wheel. Replace in reverse order. Very easy.

I removed the bucket and then took the feed screw out and replaced the end cap and reinstalled the feeder in the new bucket and put it back in place and it worked fine. This is not a hard job, you just have to pay attention to the dismantle so you can get every thing back together properly.
the breakdown and parts list was a big help.

With a socket set wrench this is the second time it happen no problem

Watched a Utube video

Ridiculous how easy it was, REALLY!

There is a plastic flapper valve that is spring-loaded in the closed position that prevents ambient room air from entering the freezer compartment via the ice chute. The Ice Chute Seal is a simple flexible (rubber-like) disk that just slips over the circular flapper valve. With the freezer door open one can see the flapper valve down the ice chute and one can reach it easily from the outside of the freezer as well. The Ice Chute Seal has 3 notches that make it very easy to remove the old seal and replace it with the new seal. This can be done by feel. I removed the old seal by pushing the flapper valve open with one hand (from the inside of the freezer door) and could then peel off the seal surrounding the flapper valve with the other hand. Once the old seal was removed I slipped the new seal around the flapper valve. No tools required, no screws needed to be removed. The problem I had with frost/ice build-up was solved; there is no more ice/frost build-up inside the freezer near the top of the ice chute. The old seal LOOKED OK but was obviously a bit too stiff to seal the opening against the warm, moist, ambient room air. I was most happy to see that this solved the problem and that it was so easy to do (really less than a minute or two!).

Work was done by service tech. I ordered the arm for my mom to save time when tech came back to do the job correctly.

Took auger apart laid out sequence as removed parts replace the same way . Parts have to go back like they were removed.

Followed the instructions in the video provided via email from Partselect
However, the part received was the opposite design of the part removed.
It appeared this could be left hand right hand choice of part. Moreover, the button on the switch that turns the light off/on when door is open/closed was not functional due to the part being the opposite of the part I was replacing. I tested the switch I was replacing and it appears this is not the problem. I think the light socket is the problem. I am 69 year old female and capable of doing small repairs, but limited knowledge of electrical so having to troubleshoot by trial and error. Thank you.