A1RXNGFYB00 Amana Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from SALINA, KS
- Parts Used:
- W11700559
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
3 screws
Ice maker fit perfectly over 2 top screws. I tightened them and put the one on the bottom. I was done in less than 10minutes. Everything fit perfectly as expected. Couldn't have been eaiser. Parts Select is my go to online store.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from MEDIA, PA
- Parts Used:
- WPW10189703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
refrigerator was not cooling
Swapped out evaporator fan motor, solved the problem!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from SACRAMENTO, CA
- Parts Used:
- W11700559
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Installed Ice Maker in Freezer
Installed ice machine components using kit and included instructions. Easy! Ran a copper line from under sink valve to back of refrigerator under the floor. Drilled two holes to run copper line. Plumber turned water off and replaced single valve with a double valve (one line to faucet and the other for the copper line). Installed shut off valve and filter at the other end of copper line. Then stainless hose to refrigerator. Everything went smooth. Double check the factory installed plastic line from the electric valve to the inlet for your freezer. Mine was barely inserted and leaked. I pushed it in all the way and it is fine now... Ice maker works really well! Wish I had done this sooner!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from MEMPHIS, TN
- Parts Used:
- 2159061
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Socket set, Wrench (Adjustable)
Rerigerator was leaving a lot of condensation on top shelf in refrigerator.
Removal of the door gasket went quite fast. First i needed a 8mm wrench. That what I didn't have. Got the socket set, not the wrench. Tried adjustable wrench, went slow. I slowly got the bolts out. Putting the gasket on was slow. Then I get to the last corner, was awful for me. I finally get it on. Putting the freezer door back on 1st went crazy. I finally looked on top of refrigerator, saw (3) bolts, removed them, installment went easy from there.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- asberry from SAINT LOUIS, MO
- Parts Used:
- WPW10189703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
first a loud noise than noise stopped then the refridg. stop cooling like it should
after finding out what could be the problem I order my part which I got around 3 days unboxed it and replaced it in the freezer component which I had already dismantled made note how I took it off and replaced it in the same way took about 25 to 30 minutes quite easy for me was grateful for the solution and proud of myself after replacing it and it began to work now it's freezing and getting cold as it should Thank you my part store
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from HELENDALE, CA
- Parts Used:
- WPW10662129
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
freezer would not freeze
inst said,"50 pct of the time this calls for new capacitor," so we changed the capacitor. Same prob. It also said,"25 pct of the time it's the bi-metal thermostat" So we ordered it. We removed the plastic rear panel from inside the freezer comp. using small nut driver. Here we found much ICE surrounding the defrost unit, three inches thick. We thawed the whole mess. and the freezer has worked fine ever since. I think my habit of getting ice cubes from the inside container rather than from the ice cube dispenser, had kep t the freezer door open too much, interfering with the normal defrost cycle and allowing ice to build up over time so that it finally defeated the system. My new rule, "get ice cubes only from the front."
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from MONTESANO, WA
- Parts Used:
- WPW10468555
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Track on pull out door cracked
Sent model #..all of maytag parts have part # printed on them..snaps off and new part snaps on!!! Great!! They do have assistance to help you repair,but wasn't needed..i know who to order from now for any appliance!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bernard from DONALDSONVLLE, LA
- Parts Used:
- W11745278
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
door hinge broke.
Removed door and replaced bushing bracket was ok.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darlene from Philadelphia, PA
- Parts Used:
- WP2254473
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
I had taken freezer door off when moving and misplaced the one of the hinges.
I attached the hinge and secured it with screws and socket wrench.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacqueline from LEXINGTON PK, MD
- Parts Used:
- WPW10662129
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
No cold
Like you video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adam from GLOVERSVILLE, NY
- Parts Used:
- WPW10662129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Plugged it in.
Not so good that was not the problem. Fan is not seized and all the lights work and display is not on but lights up as well. No start once plugged back in after 15 minutes of being unplugged. Nothing same no change.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from FORD CITY, PA
- Parts Used:
- WPW10662129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Freezer occasionally had a temperature alarm.Clicking noise also.
Was told capacitor was problem 90% of the time.Capacior was not the problem.Bad start relay.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Colorado Springs, CO
- Parts Used:
- WPW10662129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
freezer and refrigerator compartments not cold enough
Used the suggested problem list here to narrow down that the repair was most likely the run capacitor. Poped the new one in and I now have better control of my compartment ranges. I have a temperature gauge in each compartment. Check them every opening of the doors.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from Lancaster, CA
- Parts Used:
- WPW10662129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
compressor not running
Removed the access panel on back of unit located the Run Capacitor on the compressor and removed the bad one and put the new one on and pugged refrigerator back in and it started up and works fine now
Was this instruction helpful to you?
Thank you for voting!