A1RXNGFYW00 Amana Refrigerator - Instructions

I simply watched the repair video and did it! Super easy, needed start device and capacitor. As easy as unplugging the old and adding the new. The video helped and gave me confidence. Wives can fix fridges too! Saved me $2500. Looks like I'll need a new excuse if I want a new fridge.

Viewed the viedo - it showed what to do

googled the model of ice maker and refrigerator, ordered replacement ice maker from Part Select. Received next day, installed it in 10 minutes and it worked like a charm.

I removed a few items from the freezer to make room. Husband took out the old ice maker. (We were sure it would require moving the refrigerator out which would have been a huge undertaking given the tight fit) To start he simply replaced the ice maker with the new one. I started watching...and even though it says that it will take up to 24 hours to make ice, it began making ice probably within an hour! After about 6 batches, I threw those out. (just in case there was anything in the line that would contaminate the cubes)It is obvious that the old one had not worked properly for a long time! The ice container is full to almost over-flowing! It has not been this full in a very long time, as I use ice every day! Simple fix! And might I add...LIGHTNING FAST DELIVERY!! It was here in two days! We are thrilled!!!!!

I watched your repair video, read the instruction enclosed with the icemaker and made the repair in about 15-20 minutes. There is an issue that others need to be aware of once the water pump is repaced and the tubing is connected and the icemaker is installed and turned back on; it take 20-30 minutes to pump the air out of the line and the for the water to actually fill the the fill tray (you made the install correctly, the delay in filling is not covered by either the video or the book just be patience don't disconnect and reconnect anything it will eventually fill and make ice and less than 48 hours). This vendor offers 4 star customer service at a fair and resonable price (I priced the parts separately prior to purchase and the kit is the way to go). I received the product within 3 days, shipped groung delivery. I would use your products and online service advice for installation on other appliances in the future if needed. You have earned my trust, and repeat business in the future; and I will gladly recommend you to others. Your customer focus and service is second to none. I am a fully satisfied customer!!sincerely, a. Walker

1)pry out the old/defective light rocker switch with a screw driver (flat head) and pull out the cables 2)unplug two connectors at the end of light rocker switch 3) connect new light rocker into two connectors 4)push the wires inside and put back new light rocker switch

I did exactly as the video showed. I popped out the old switch, disconnected the two terminals, connected the new switch and put it back. The light now works! The refrigerator is over 25 years old and the switch works! What a great website this is. Couldn't of done the job without Partselect's help.

Took socket out and replace it with new one. Very easy. W saved alot of money doing it ourself.

After plugging in the new relay to no avail. I replaced the thermostat. That fixed the problem.

Unplugged refrigerator. Unplugged ice maker and took out three screws holding ice maker. Put new ice maker and attached three screws. Plugged ice maker in. Plugged refrigerator in and ice maker began working. Threw out first ice cubes made. Unit now working fine.

1. Turn thermostat down to ensure cooling cycle turns on. Open freezer compartment and listen for air flow/fan. If no air flow or fan, but compressor seems to be working, then proceed to next steps. 2. Turn thermostat up to shut off refrigerator cooling cycle. 3. Open freezer and remove wire shelf (if installed). 4. Using nutdriver or socket set, remove screws securing metal panel on the back wall of the freezer interior. 5. Pull metal panel out to expose evaporator fan and evaporator coil. 6. Ensuring area around fan is clear, turn thermostat down to again start cooling cycle and check if fan operates - if not, then fan needs to be replaced. 7. Turn off refrigerator and unplug from electrical outlet. 8. Order replacement fan (unless you happen to keep one in stock). 9. Remove two screws securing fan and fan bracket assembly to back wall of freezer, note wire connections to fan (red, white and green), disconnect wires and remove fan assembly. 10. Gently pull off fan blade, it is a compression fitting. 11. Remove two screws holding back and front fan brackets together and remove fan motor. 12. Remove rubber gasket from front and back of old motor and insert then on the new replacement fan motor (these rubber gaskets align to openings in the fan brackets, thereby holding the motor in place when installed back into the brackets). 13. Reinstall fan brackets onto new motor matching how the old motor was assembled. 14. Press the fan blade onto the new motor shaft. 15. Reinstall fan motor assembly onto back wall of freezer. 16. Reconnect wires to new motor as they were previously connected to old motor. 17. Reinstall back wall metal panel that covers the fan motor assembly and evaporator coil. 18. Reinstall wire shelf (if applicable). 19. Plug refrigerator in and adjust thermostat to normal setting to initiate cooling cycle. 20. Open freezer and listen for fan and airflow, if you hear it operating correctly, then close freezer and refrigerator and confirm temperatures after refrigerator has cycled through one full cooling cycle - adjust thermostat as necessary. 21. Tell your spouse or significant other that for less than fifty dollars you just saved the price of replacing the refrigerator.

The repair was very easy, unplug ref. open freezer door, and remove base plate, then remove screws on back plate. I had to tilt top of back plate to remove from freezer. This gives you access to the evap. fan Pull of the three wires, and remove screws from fan bracket, which bolts to the back of ref. Remove fan motor from bracket (2) screws, remove motor, and put replacement motor on bracket, pull fan blade off old unit and push on new motor shaft. Reverse the installation, and you are done. Pretty easy.

Simply removed the old icemaker and replaced it with the new one. Reqires removing 3 hex head screws and wiring harness, then reconnecting the new unit.

I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.

I had ordered some other parts for something entirely different off your website and service was great. So after almost ten years of a dark refrigerator, because of a defective switch, I decided to see if you had the part to fix it... You did and the part got here in 3 days. I had a working light switch and all the light in the world where my husband needed it most (in the fridge). It took me at the most ten minutes to replace the part. All is well now and I have a happy husband who can find the leftovers just fine. Thanks for your great service!