ABB2224WEB3 Amana Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Daniel from LAKE CITY, FL
- Parts Used:
- WPW10436250
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Freezer freezing up. Frost everywhere.
Old gasket pulled of easily with no tools. New gasket was placed on floor and heated with blow dryer to straighten. Then installed new gasket by pressing in with my hands. Noticed that the old gasket was hard and not flexible. All was great. Fit perfectly. No frost after a week. Happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Winston A from Brooklyn, NY
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Raplaced switch
Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- J. David from BRENTWOOD, TN
- Parts Used:
- WPW10350564
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Capacitor shorted out due to power surge.
Access back of unit, lower left corner. Remove wire capacitor retention clip. Unplug cold capacitor, plug in replacement, reinstall wire retention clip, test.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DANA from ASHTABULA, OH
- Parts Used:
- WPW10671238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Center Crisper Rail Broke Off At One End--Drawers Would Not Slide And Hang Right.
Very easily removed top shel glass above crisper--removed old rail by lifting up--and place new one in slots provided---simple!! Part was delivered in less than 3 days-------very fast and cheap !!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from ATLANTIC BCH, FL
- Parts Used:
- W10443315
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Freezer Compartment Gasket Replacement
My freezer compartment gasket was torn and needed replacement. This was on a bottom freezer Kenmore refrigerator. I couldn't find directions for how to take the freezer compartment door off, and figuring out how was the hardest part. Here are the instructions:
1. At least 24 hours prior to starting, remove the gasket from the packaging and lay it out in a warm area, to allow the creases to come out.
2. Unplug the refrigerator.
3. You will have to take BOTH doors off, so put at least the freezer compartment contents in a cooler so they don't thaw. Also remove all items from the refrigerator and freezer door.
4. Remove the refrigerator door first - remove the plastic cover from the top hinge, then remove the 3 metal screws holding the hinge in place. Lift the door up, and it will come right off. Set it aside.
5. Now remove the freezer door - there is one bolt head, for the top hinge pin. Remove it, and lift the door up and put it down on a table.
6. Towards the center, pull up on the old gasket, and use a pair of diagonal cutters to cut it in half. It will take a few cuts, but eventually you will get it out and cut in half. Then remove the old gasket.
7. The new gasket simply presses in. Start at two diagonal corners, then press the other two corners in, then do the straight sections.
8. Now replace the freezer door, then the refrigerator door, plug in the refrigerator, and put the contents back in.
1. At least 24 hours prior to starting, remove the gasket from the packaging and lay it out in a warm area, to allow the creases to come out.
2. Unplug the refrigerator.
3. You will have to take BOTH doors off, so put at least the freezer compartment contents in a cooler so they don't thaw. Also remove all items from the refrigerator and freezer door.
4. Remove the refrigerator door first - remove the plastic cover from the top hinge, then remove the 3 metal screws holding the hinge in place. Lift the door up, and it will come right off. Set it aside.
5. Now remove the freezer door - there is one bolt head, for the top hinge pin. Remove it, and lift the door up and put it down on a table.
6. Towards the center, pull up on the old gasket, and use a pair of diagonal cutters to cut it in half. It will take a few cuts, but eventually you will get it out and cut in half. Then remove the old gasket.
7. The new gasket simply presses in. Start at two diagonal corners, then press the other two corners in, then do the straight sections.
8. Now replace the freezer door, then the refrigerator door, plug in the refrigerator, and put the contents back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Monte from Longview, WA
- Parts Used:
- WPW10534162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I purchased a display model that was missing a part.
Snapped on the new toe grille.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- anthony from HAVELOCK, NC
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
changed the light bulb still would not work so I figured it was the switch sure enough.
I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from SMITHFIELD, RI
- Parts Used:
- WP12825803
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
I had a loose fitting old condensor fan blade on my new motor.
I made a temporary repair by drilling the old blade plastic hub and put a small screw in it to hold it on to the shaft until the new blade arrived. The new blade came in within the two days I needed before Thanksgiving. I removed the old and pushed on the new. There were 8 screws on the back guard and two to hold the motor on. It was a snap.
Thank you PartSelect.com The wife is very, very happy now, we had 51 coming over for Thanksgiving. :)
Thank you PartSelect.com The wife is very, very happy now, we had 51 coming over for Thanksgiving. :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THOMAS from WILLARD, OH
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
defective light switch
inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rich from WINSTED, CT
- Parts Used:
- W10619951
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Water not draining to pan. It caused an ice build up under the freezer draw
Remove the grate at the back of the refrigerator. Remove the existing drawn tube. Replace the exiting drain tube with the updated drain tube. Check to see if water was draining properly. Replace the grate. Sit back and have a beer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from LAKE CHARLES, LA
- Parts Used:
- W11447232
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
One of the light bulbs went out on my Whirlpool refrigerator.
I changed the bulb but it still didn’t work. I ordered a bulb holder and replaced it and it works properly now. It was an easy repair, remove the bulb, gently pry the bulb holder out with a screwdriver and snap the new one in.
It was useful that under the description of the part in the catalog, it showed that this part was often used to repair this issue. The service was great and the delivery was fast.
It was useful that under the description of the part in the catalog, it showed that this part was often used to repair this issue. The service was great and the delivery was fast.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jake from RICHMOND, VT
- Parts Used:
- WP67001054, WP67001053
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Glides were broken
Just swapped out new for old. Couldn’t be easier!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from PASADENA, CA
- Parts Used:
- WPW10671238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Center Crisper rail
Take everything off the top self, lift the self install the new part ,put self back in place and then install the drawers again. Took minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Megan from NORFOLK, VA
- Parts Used:
- 12002497
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Boyfriends freezer door wouldn’t shut completely
I got really tired of taking food out covered in icicles and stabbing a huge block of ice out of the bottom. Turns out all he needed was a little wheel with cogs and I looked up the sticker model number on this site and clicked the part of the fridge. So simple, wish I would’ve done it sooner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from GEORGETOWN, TX
- Parts Used:
- WPW10534162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broke my original Kickplate Grille
knelt down, positioned replacement kickplate; popped into place, stood up!
took longer to open the box and peel bubble wrap off item than to replace it!
took longer to open the box and peel bubble wrap off item than to replace it!
Was this instruction helpful to you?
Thank you for voting!