ABB2522FEB2 Amana Refrigerator - Instructions

I broke the glass in the frig and found partselect and ordered the new glass and had it in 2 days. Very fast shipping.

Popped off the control panel at the top behind the door. Found the thermistor and replaced it, cutting the wires and splicing the new one in. Immediately the warm section of the refrigerator was getting below freezing temperature readings, so the cooling vent was not opening. I put the old one back on and the temperature readings went back to being accurate. So this was not the problem. I believe now that the fan somehow is not blowing enough cold air up. So now I'll probably buy a fan motor and maybe a blade and try that. Otherwise the computer module I priced at $500 so I hope it isn't that. I replace the fan motor a few years ago already.

Failure detected as Damper Control at upper rear of compartment would continuously open/close, would never stay open or closed. Sometimes the main board would turn it off (maybe a low thermistor limit?), but it would stick open a bit, and keeping letting freezer air into fridge. Could have potentially been control board, but as it turns out after disassembly of the defective damper, the internal microswitch was stuck in the closed position so it wouldn't shut off the motor. Easy fix by gently pulling the cover off the damper control, pull out Styrofoam encasement, then a phillips to remove the damper assembly. Gently push tabs to release wire connectors. Reverse the process and you're done! If I really wanted to go on the cheap, I could have just changed the microswitch, but that looked like a shaky maneuver at best. This site saved me on this one, so happy to share my experience with this Maytag and its nasty habit of freezing my milk and eggs!! :)

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

Let the ice in the freezer melt while installing P trap drain tube

First of all I want to thank Michael from Carlisle,PA and this site for publishing Michael's info on the wiring specifics on the new 3 connector Start Relay ( WP2262185 ). The original relay only has 2 connectors The 2 orange wires which are combined to one female connector need to be clipped and separated each to its own connector. Refer to Michael's blog as to which wire goes to which connector on the Start Relay. I replaced the Run Capacitor, Start Relay and Overload just to be safe. The Start Relay was the actual culprit.Thank you for an excellent website!

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

When the gasket is delivered it will be folded. You will need to unfold it and leave it on a flat surface for several days. Keep it as square as possible, and heat the kinked portions with a hair dryer on high heat and slow fan while molding kinked portions with your hands for 30 to 60 seconds at a time. Do that 2-3 times per day. When it looks 90% uniform with the non kinked portions, you can install it. Installation takes less than 10 minutes. Clean the metal edge of the freezer well. I recommend taking the door annd frame off (This is remarkably easy. THe door and frame pretty much lifts up and out after you hold the rail clips inward) because the lower edge is so close to the floor. The just pulll off the old gasket. There are no screws or clips. Starting in any corner, press new gasket into place. Go around the perimeter several times to make sure it is pushed in fully and evenly. Then reinstall the door and frame.

Simple placement of new glass pane into crisper top

Removed the top glass above the vegetable drawers and slipped the center rail in place. And I would like to add that I would do business with this site again!

Snapped in new part

Don't try and remove the front/handle from the broken pan, you will break it and its double the price of the pan, just use the small hammer to break the pan into smaller pieces and remove handle from them then the handle will just snap onto the new pan. Piece of cake!

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

I made a temporary repair by drilling the old blade plastic hub and put a small screw in it to hold it on to the shaft until the new blade arrived. The new blade came in within the two days I needed before Thanksgiving. I removed the old and pushed on the new. There were 8 screws on the back guard and two to hold the motor on. It was a snap.
Thank you PartSelect.com The wife is very, very happy now, we had 51 coming over for Thanksgiving. :)