A8RXCGFXW00 Amana Refrigerator - Instructions

First I had to figure out how to get the old unit out so I could work on it. The three screws that others wrote about were the ones that hold the motor in place. There are 3 screws holding the ice maker in the frame, along with one screw covering the electrical connection. The electrical connection was difficult to unplug because the locking tab was on the back side of the connection and with no room to work in the freezer it didn't become apparent until several frustrating minutes went by. There were no instructions provided, the picture on the ordering page showed the complete ice maker, and for $80 you get a printed circuit board with a small round item which must be the motor/timer control. The two plastic parts for moving the ice from the ice maker were included but not replaced because I didn't notice them until I had finished replacing the ice maker back in the freezer and wasn't going to start over again.
Once installed, there wasn't any noise, even of water flowing like the old one, could not tell if the unit was working or not. In the morning there was new ice in the bin indicating the repair had been successful. This is like anything else, if you have done it before it is a 5 minuter job but when you have to look at it and try to figure it out it takes a bit longer. All in all, it was simple enough, I was expecting a complete ice maker unit like was in the picture when ordered but only the motor module was actually needed.
We have another refrigerator/freezer that has an icemaker that is over 20 years old and has never been repaired, it is a Sears model though, probably made by Whirlpool or someone else.

I took out the old socket by moving a clip. Reattached the electrical wires, clicked in the socket and that was it.

The instructions are practically no help, but if you study the diagram, you can figure out the one screw you need to remove. Then the icemaker lift off of two brackets. I couldn't see how to use a screwdriver to unlock the bracket, but just applying mild pressure and pulling it forward brought it right out. I didn't have to change anything with the plug already intalled so it was very easy to pop in, lock the plug, pop into brackets, replace screw and I was in business. 24 hours later I had a bucket of ice! 15 minutes to figure out how to get old out and 5 min to replace new one. Fairly easy. Read posts here to get hints!

i noticed that no water was getting to the ice maker. rather than messing around with parts, i bought the entire unit. easy to remove old one and install new one. thanks...ice started again in about an hour. unit cost less than a service call!

The plastic part that connects the fresh cold water to the ice maker in back of the fridge cracked.
Do to the fact that Whirlpool has the part stick out on the back top part of the fridge. So if you push the fridge just an inch too far back the plastic part will crack.
I ordered (The Part S&H)- came to about, $11.00.

1. Turned off the cold water under the sink.
2. In the back of the freezer section. I unscrewed the two screws that held the old broken part to the fridge.
3. I opened the freezer section and cleared out the top shelf till I could see the back of the fridge.
4. I removed the old plastic part by pushing & wiggling it about forward and it then extended out the back of the freezer side and then I pulled it out the back and it came out.
5. I slid the new replacement part in basically the reverse of step 4.
6. I connected the hose in the back. To the new, replacement plastic part, that fills the automatic ice tray with water.

7. Once finished I glued a small 2”x2” piece of wood next to the new part so the fridge will never get too close to the back wall so to never break that part that sticks out again.
Before just a small bump could break the part and water is everywhere and this leak could happen slowly at first and the next day what a mess.
Some fridges have this part recessed into the back of the fridge so this would never happen as my other fridge has.
Also, this might seem like more work then it was. It was very simple. I was scared I'd screw it up, but just did it step by step. If I had someone do it. It would have cost me a bundle.
It took more time to type this, then to do the work.
I had no instructions to follow, but again, was easer then I thought it would be.
I hope that this was helpful,
Jim Vourakis

Removed brokent tube fitting from the compression nut.
Removed two screws holding the fill tube. Removed and replaced the fill tube. Direct replacement, no cutting tube length. Reconnect water line to the new fill tube.......Done.

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

removed two screws and pulled part out of the unit. The local appliance store said they needed model and part # to try to identify and order the part. Found part select online, found the part immediately, ordered the part for $4.50 or so. Part was delivered in 2 days! Very easy installation and the part works perfectly. Thanks so much!

Just put the hinge on and screwed on

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

I removed three sheet metal screws, unsnapped the electrical pigtail. Then snapped out knock out on new maker. Matched the electrical connection, pushed it in place. Finally set new one in place, leveled it, tightened the scews and walked away.

Followed instructions on your website

It was exactly as everyone else described--remove old ice maker, unplug, plug in new ice maker, attach new ice maker. 3 screws, 1 plug. My plug was the one on the ice maker not on the refrigerator (ie I used the wiring/plug that was already in the freezer).

On my particular model refrigerator I only needed to remove one screw and disconnet the plug. I then slid the unit out. The new ice maker did not come with the plastic sled that was attached to the old unit. I removed and attached the sled to the new unit with 3 screws.

Loosened two top screws using a hand held mirror and screwdriver and removed a bottom screw then unplugged the unit inside. Five minutes and repair was complete. Easy as that!