A8TCNWFAW02 Amana Refrigerator - Instructions

Great service. Unpluged old switch and pluged in new one. Works great

Used a screwdriver to pry loose the old switch, swapped wires to the new switch and pushed it into the opening. Took about 2 minutes.

After disconnecting the electricity. I followed the instructions as indicated in the "HOW TO" article on the website. I used a steel putty knife and pried the light switch out of its retaining hole. I worked the right side the most since this is the side with the retaining clip. After I removed the switch I transferred the two electrical outlets to the new switch and easily snapped it into place. Engaged the electric power and tested the switch.

Screwed in light bulb and glass protector

very easy

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!

Sincerely, Ron Marshall, Billings, MT

Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!

I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.

taped the door shut ,measured a block of wood and stuck it under the door for support.....unbolted bottom hinge,slipped on hinge bracket and reassembled.no muss no fuss.

I spent several hours defrosting the unit. Making sure the vents were all defrosted and free of ice. The part replacement is fairly straight forward; remove the thermostat, cut two wires, reconnect the wires following color codes, attach to coil and restart. And, "Yippie!". Nothing. Zilch. Zero. Because I could not connect with the online repairman, I spent 40 bucks for nothing; problem was not resolved. Thanks for taking my money. I'm bummed and with just a little less money in my pocket. Never again will I ever purchase another Whirlpool product. Or buy from your outfit again (because of the over priced part). I replaced a 25 year old 'working' General Electric fridge for this junk that sat in the warehouse for four years before this was delivered to me in 2018 and sold to me as a "new" appliance. This was found out only when it crapped out and I needed to have it checked out for repair. Oh yea, I only had the comment section and the part recommendation to go by, and the latest comments are at least two years old. I'll be surprised if this even gets posted.

unscrewed the old one! installed the new one! That simple. And I'm female, how easy was that!

Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

After ordering the ice-maker, but before it had arrived, I installed a valve in the pex water line in the room right below the fridge. I had to rent a pex clamp kit from Home Depot. It cost $8 for 4 hours and came with the crimpers and band cutters. I then ran a poly line to an in-line filter which I mounted to an exposed stud and fished the line up the wall and out a small hole I drilled behind the fridge. When the ice-maker came, it took less than 30 minutes to install and start my first batch of ice. With the in-line filter, the ice forms with practically no sediment flakes. Part Select was the only place I could find a replacement ice-maker. In addition to the parts in the ice-maker kit, I had to buy 12 feet of poly water line, a ball-valve, the in-line filter and a compression fitting. A total of $20 at my plumbing contractor store.