CSDI25C-P73320-52W Amana Refrigerator - Instructions

followed repair help directions

I watched the video to get up the courage to try the repair myself. I figured out the refrigerator model umber and ordered the parts on line from Parts Select. Parts showed up in a few days. Pretty easy so far. Under close scrutiny of the wife, I unplugged the refrigerator. I used a nut driver on my cordless screw gun to remove the back cover and valve. I removed the plastic water lines and electrical connectors from the old valve and attached them to the new part. Everything matched perfectly. I replaced the valve and back cover. I pluged the refrigerator back in. It might have taken 20 minutes total. The wife has her icemaker back online and I'm a hero! Thanks Parts Select!

I knew the repair wasn't difficult. It was a matter of finding the replacement part. Luckily, I found the part via the internet on your site. Lucky for me, there was an installation video!! These videos are worth 1000 bucks!! Never have encountered a site with installation videos before. It gave me complete insight as to how the job was sequenced. I'm a very visual person, so videos are the perfect helper for me. With fewer and fewer affordable local service companies around to fix problems like mine, your site gave me the complete confidence to easily switch out the condensor fan. I completed the repair for about $63.00. Your site ROCKS! Keep up the repair videos because they are awesome and extremely helpful. I felt like your pricing was competitive for this item. Thanks again!!

Removed bottom air vent and removed/ replaced defrost timer by removing 4 bolts with nutdriver, disconnecting the plug connections and then reversing process. Very simple. Unfortunately, this did not solve the problem. Next step was replacing the thermostat. Again a simple procedure, but required removing freezer shelves and the rear panel. You have to exchange one lead from old thermostat to new, but very simple. Again, unfortunately, it did not solve my problem. Temp still down around 24 degrees F but needs to get to about 0 degrees. In both cases, I noticed no frosting up on the evaporator coils, just a little on the tubing that the thermostat attaches to. I'm thying to decide next step. Any help will be appreciated.

Well I could what laid on the floor and replaced it but I didn't I emptied refrigerator laid it over change the motor then stood it back up actual work about three hours

The video of the repair is a helpful guide, but my refrigerator has the compressor very close to the condenser fan motor. With the compressor comes the copper tubing that is all in the way. I had to carefully bend them now and then to allow me to get my hands in position. The how to is easy, but the working with tools in cramped quarters was difficult. I think my Maytag side by side model makes for this job to be difficult, maybe yours may not be so bad. I took a couple of hours to complete. After the first hour, I covered the bare wires, and plugged the frig back in so it could do some cooling. I placed a small in front on the condenser to blow across it. Had a little break, then finished the job.

removed condenser fan -located behind refrigerator next to compressor, Not much clearance to work, there are 3 screws to remove from condensing motor,sounds easy but clearance is lacking to remove them ,(takes alot of PATIENCE). Then you have to remove the fan blades to be able to get clearance to remove motor!! I wouldn't reccommend trying this repair unless you are a pro.

I have an Amana freeze and I followed the procedure in the video. Which is very good! However on the Amana Model there two slight differences in the procedure that I felt I needed to do. The first one is, the condenser fan bracket is attached to the Freezer chassis with 4 screws, not three. The removal and installation of the back screw by the fan is a bear. I removed the other three and it allowed me to rotate the fan slightly to get more access to the fourth and did same on installation by just starting the 4th screw and then tightening it later. The second issue was my new fan hit the housing when I spun the fan. When I looked at the old one. It had a phenolic washer, between the fan and motor which spaces the fan out about a washer thickness from the motor. When I tried to remove the old one it broke in four pieces due to age. So, I made my own with a washer that I super glued to the motor housing after carefully centering it on and clearing the motor shaft . Seemed to work with out any more noise or balance issues...Thanks, your delivery was blindly fast and video was great!

Removed bad motor with socket set and pliers then removed the connectors from the old motor and soldered them on the new one. Then installed new motor. Works like new! Problem Solved! Easy fix!

Easily removed the old solenoids and installed the new one, reconnecting water lines with no problems. Icemaker now working properly.

I found the condenser fan was not working so I bought a new condenser fan kit and installed it. Fixed!

I replaced the dual solenoid valve and made sure the ice cube tube was clear of any ice. Sure enough, it works and the nice old neighbor lady is happy.

I removed the back cover on the freezer cabinet and discover that the evaporator coil was cover with froze and ice. I then though that one of the three component of the automatic defrost system: timer, thermostat or heater coil has stopped working. I measure the resistance off the heater coil and obtained a 54 ohms reading so that was good. I did not did a very good job with troubleshooting the timer and thermostat since I conclude that the timer was bad. I ordered and changed the timer but turned out that the faulty component was the thermostat which I replaced and the refrigerator started to work like a charm :)! The harness was not exactly the same so, I has to cut and strip two wires and reconnect; beside that everything was fairly easy to do. Thank you!

My husband put in in, no problem and all is well. My husband is a mechanic for large machinery/motors so installation was no problem. Thanks, better than buying a new fridge!!!

We described the problem of the freezer and refrig not keeping cold and with the suggested parts to order and the amazing videos to follow my husband repaired it. We have one part we ordered for temperature control (RO16088) and are waiting to see if it needs to be installed. What a joy it was to hear the sound of ice cubes being made. The refrigerator went out during very hot weather. Thank you again for your wonderful help and videos. Paul and Mary Jo