85151-P1117109W Amana Refrigerator - Instructions

First, I shut off the water going to the refrigerator, then removed the ice bin. Then I loosened the two screws on the top of the ice maker (the one toward the front was a little tricky, since you can't see it at all), then removed the screw that fastens the lower bracket to the side of the frig. Then I lifted up on it slightly to remove it from the two upper screws, then unplugged the wiring harness from the side of the refrigerator and lifted the whole unit out of the frig.

I then removed the plastic cover on the front of the ice maker, pressed on the tab to remove the wiring harness from the old ice maker, and installed it on the new ice maker. I then removed the metal arm from the old ice maker and installed it on the new unit as well. The last part that I moved from the old ice maker to the new one was the lower bracket, as the bracket on the new ice maker was bent during shipping.

Once those parts were swapped, I put the plastic cover on the new ice maker, plugged the wiring harness back into the side of the frig, routed the fill tube into the back on the ice maker assembly, and set the unit back on the two upper screws. I then put the screw back in the lower bracket, tightened the two upper screws, and then put the ice bin back in and turned the water back on. After a couple of hours, I threw out the first couple of batches of ice and it is now working as it had in the past.

I also noticed, when looking at the old ice maker, that the black plastic coating was coming off the ice cube tray, so it was a good time to be replacing it anyway. Overall, a very easy job (I was prepared for swearing, parts being slightly off, etc.) and it would have been a shame to have paid someone to do it.

I used this part on a little, under-counter U-line ice maker that is the best little ice maker in the world. The single solenoid part from U-line cost more than twice as much as the generic GE one I ordered from you. It arrived in only 2 days and I was able to just remove the inlet and outlet line from the old solenoid and unscrew the bracket to remove it. I used the included bracket and one screw affix the new one to the ice maker, then just pushed on the inlet and outlet lines, tightened them on, plugged it back in and In about 20 minutes from start to finish, it was back in business, cranking out ice really quick as it was before. Could not imagine summertime in Texas without my U-line,,,Thank you!!!

Took out three screws, kept the little plastic cover on the bottom screws and the screws--they did not come with the new handle. It took less than 5 minutes to do the whole job and while it was off I got to really clean my frig. Thanks for the quick delivery!!

I didn't. Don't know how to get to light bulb to change it for this specific model

The Ice maker unit had to be removed and the shaft had to also be removed, which required dis-assembling the motor drive. The thickness of the shaft and the bearing fill cup prevents it from simply pushing it in place. Other than that I have Ice.

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

Did the troubleshooting with online instructions and a multimeter. Bought the new thermostat. Disassembled the freezer compartment using a nut driver to expose the evaporator, etc. The thermostat was easy to locate in the upper right hand corner. The new thermostat had one wire that didn't have the correct connector on it so I stripped the wire back and used a crimp connector and heat shrink to attach the connector from the failed thermostat. After plugging the new thermostat in I ran the refrigerator for 15 minutes to cool the thermostat and then rotated the defrost timer to the defrost position and tested the new thermostat. Reassembled the freezer compartment.

Removed pin holding the wheel along with leveling screw. Put new wheel in place, replace pin and screw. Done...very easy.

This was the third icemaker replaced since January 1999. Improvement need to be made in the design of the icemaker so that more than 2-3 years of life is available.
The most difficult part was disconnecting the power plug in the back of the icemaker. You must squeeze the upper and lower tabs together and pull out at the same time to disconnect. Once this is done, take out one nut head screw, lift up on the icemaker and remove from the hanger. Be careful that you don't break the plastic tabs on the hangers. Replace new icemaker in reverse, feed water supply where it must go in the back, resnap onto hangers, replace the nut head screw and snap in the power plug. It took about 2 hours before the icemaker began making ice. It has been working fine ever since. PS. I saved about $200.00 over having a repairman come in and replace the unit.

First I removed the two screws that held the top of the handle in place. Then popped off the bottom holder. Replaced the broken handle with the new one, replaced the screws and snap on section and now have a nice looking refirigerator with a handle that works.

Pretty simple really after reading online some other owners' experiences. This is a bottom freezer unit. Remove the ice maker, the tray slides, and the back cover of the freezer box. In my case I had to thaw it out with a hair dryer as the cover was frozen in place. I checked the old 'stat and found it was bad; I temporarily wired the leads together until the new 'stat arrived. It does allow the refrigerator to warm up during a defrost cycle but it beats de-icing it twice.The defrost 'stat is clipped over the refrigerant line in the upper right corner of the box. Resistance was 65k ohms and wouldn't close on low temp (tested by clipping it to an exposed refrigerant line in another upright freezer) but there was no obvious damage. The one lead on the replacement 'stat has the wrong connector so you have to cut off the original lead from the old unit and splice it on the wrong lead on the new one. I used an epoxy sealed heat shrink type butt splice. Reassemble and let it run. One word of warning: be careful tightening any screws as they will strip easily

removed old ice maker by taking out a couple of screws in the back of freezer,when new ice maker arrived i saw that it didn't have the same hose apparatus as old one so I easily took apart old one then took apart new one and switched them out-very-- easily done for a 61 yr old lady I might add-- also had to reinstall ice maker arm off old ice maker as new one does not come with one Then installed new ice maker in freezer I am very very pleased,sure saved a lot of money doing it my self

Removed the 3 screws that hold the ice maker in place and remove the cover and level wire. Put the cover and wire on new part and install the 3 screws. Had ice within 1 hour. A very easy job for the do it yourselfer. Suspect the heat coil that melts the cubes was not working in the old unit and cubes stayed in the tray.

First I removed the ice catcher bucket to give myself a little room and lifed the ice maker lever to make sure it wouldn't try to produce ice while I was replacing it.

I removed the bottom screw and loosened the top two with a nut driver. The ice maker lifted right out and allowed me to disconnect the electrical plug; just squeeze the little plastic levers on both sides of the plug and pull.

I plugged in the electrical connection from the new ice maker. Making sure the water spout was in place, I dropped the new unit over the two loosened top screws. I then replaced the bottom screw and tightened all three. I replaced the ice catcher bucket and made myself a martini as a reward for not spending the $75.00 to $100.00 for a service call.

Within a couple of hours it was again making batches of ice for more martinis; it was a day or so before there was enough for frozen Margueritas.

I never even unplugged the refrigerator or shut off the water supply, although I suppose it would be prudent but not necessary. Some people like me just like to tempt fate.

The repair was so quick I didn't even worry about emptying the freezer. It was so easy even a girl could do it ... no offense intended. At the equivalent of $300.00 to $400.00 per hour I wish I could do it all day. Maybe I should be a "refrigerator repairman".

Seriously, the only thing that could hamper you is a lack of confidence which will quickly be overcome in 10 to 15 minutes by a huge ego. That time frame includes locating the tools and taking a few deep breaths. Don't hesitate to give it a shot. If you can't do it you really don't deserve to have ice. It really is that simple and easy.

Followed the directions in the package. Turned off the power, removed two screws following the directions and replaced the entire unit. So easy even a Cave Man can do it. No kidding, and the best part was the fact that our local distributed wanted almost $20.00 more for the same part and I'd have to drive over a hour 40 miles to get it.