AFI2539ERB01 Amana Refrigerator - Instructions

It was quit simple. I removed the draw and the shelves above the pantry unit. Once everything was removed (2min), I removed the one side pantry bracket ( 2 screw's). Put in the new pantry bracket and screw's and I was done. I'll give it ten minutes total. easy button Thank you

Easy fix, it's right in the back of the fridge under a cover that just clips in, a piece of foam, and two screws. The hardest part is getting the clips free without breaking them. After replacement it's silent instead of making a grinding noise regularly.

Remove back cover
Remove drip thing from top to tray in the back
Remove fan motor assembly. This is squirrely. Top bends towards you, bottom pushes in to the unit. Not fun.
CAREFULLY remove copper tube that rests on drip tray
Remove tray - there are clips in the front that get released by screwdriver
Clean up
Replace new tray
Replace copper tube
Play with fan motor assembly till it fits. It doesn't look like it's gonna work until it does. See youtube videos on this.
Replace drip thing from top to tray - I forgot this one the first time.
Replace cover.

This is a simple, but squirrely, repair. Right on the border of easy (because so few tools and steps) and A Bit Difficult because of the patience required.

I broke the glass in the frig and found partselect and ordered the new glass and had it in 2 days. Very fast shipping.

I removed and disassembled the broken frame. I cut a six inch piece of coat hanger and folded in half and crimped together. Then I took pliers and made a hook that I hooked into the metal strip in the back of the refrigerator that holds the upper shelves. After replacing the frame, center rail and glass I bent the wire up under the back of the frame to provide a support. The back of the frame is weak and has no center support.

Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked

A jar was dropped on the chef's pantry lid and cracked the lid. I unhinged one side of the lid from the pantry drawer by gently pushing outward on one of the hinge pins. The lid slid out easily. I then reversed the process using the new lid and it went in smoothly. Be sure to align the lid so it rests on the shoulder of the pantry drawer. Simple task, no tools, and less than 5 minutes effort. The replacement part was perfect.

The old cover was off and I just slid the replacement part that I got from you'll, it just slid in place and snapped close. Perfect fit. Thanks guys

I safely unplugged the power from the refrigerator first before starting the repair. I then had to remove the bottom access panel which is secured with hex head screws, then disconnected the two plugs from the two failed parts that connects to the appliance compressor. After installing the replacement parts and returning power back to the refrigerator I buttoned up the access panel and I waited at least three hours to turn the cooling system back on. This allows the coolant in the compressor to settle. The two replacements parts fixed the cooling system.

Simple. Just put it on the racks provided in the fridge. The part fit perfectly and took literally 5 seconds to put it on.

Removed old shelf and installed new shelf. No tools required

Don't try and remove the front/handle from the broken pan, you will break it and its double the price of the pan, just use the small hammer to break the pan into smaller pieces and remove handle from them then the handle will just snap onto the new pan. Piece of cake!

Looked online for instructions. I had to remove the shelves from inside the frig, then pop off part of the right inside back wall. The way the 3 water lines attached to the inlet valve was a terrible design. There are plastic little collars that need to be pushed back to release the water lines from the old valve, then when you install the new valve, you need to push them back to reattach the water lines. Once installed, one had a leak. No matter how hard I tried I couldn't get the little plastic collar to disengage. I couldn't push the line in further and I couldn't get it back out. Ended up cutting the line off at the valve just to get it out. Then had to cut out the piece that was still stuck in the valve. Tried to install it again and it leaked even more. Ended up putting the old valve back in and throwing away the $130 new inlet valve because there are no returns on electrical parts. Total waste of time and money ! ! ! Not happy to say the least.

I easily ordered the part. When it came in, I just shut off the water, disconnected the electricity, and followed instructions to remove shelving and drawers. Then removed the rear interior cover, removed the old water inlet valve and installed the new one. Just a couple moldex wire connections and the 3 water lines in and out. Don't know if this is still ok, but so simple a caveman could do it. Sorry Geico.

first of all,i just want to thank parts select for sending me a second ice maker at no charge.after installing the first one and it didn't work,i talked with Heather and she sent me a new one.installation went the same as before.hardest part is getting the quick connect wire harness apart and the ice fill arm .it is working great and my home is happy.thank you!