BZ20QW-P1125511WW Amana Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- PHILIP from SNYDER, NY
- Parts Used:
- D7605116Q, WPD7605115Q
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set, Wrench set
worn out freezer and refrigerator door gaskets
removed inside door panels by removing multiple
screws- 20-30 screws which hold each panel and gasket together to the door. then remove old gasket and put new gasket in place... align new gasket to seat on plastic ridge of inside door panel.. pay special attention to the corners so they are aligned properly without any 'bulges'. then screw each panel back on to the door using the original screws removed. best done with the help of a friend to hold and align the panel while you attach each screw. also after installation with door closed - use a hairdryer to soften up the gasket and allow it to conform to the new space and door application. total time is approx 1 hour per door... i probably saved well over $100 in labor by doing this myself-thankyou part select.com for having my parts... i will visit you again once something breaks or wears out again !
screws- 20-30 screws which hold each panel and gasket together to the door. then remove old gasket and put new gasket in place... align new gasket to seat on plastic ridge of inside door panel.. pay special attention to the corners so they are aligned properly without any 'bulges'. then screw each panel back on to the door using the original screws removed. best done with the help of a friend to hold and align the panel while you attach each screw. also after installation with door closed - use a hairdryer to soften up the gasket and allow it to conform to the new space and door application. total time is approx 1 hour per door... i probably saved well over $100 in labor by doing this myself-thankyou part select.com for having my parts... i will visit you again once something breaks or wears out again !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Manhattan Beach, CA
- Parts Used:
- D7605116Q, WPD7605115Q
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Over time the door gaskets had deteriorated to the point where the air loss in the freezer was causing ice/frost build up in the area of the freezer control.
I began by loosening the door gaskets by backing off the screws about 2 turns with the nut driver. The gaskets pulled off easily. I then heated the new gaskets in the clothes dryer on med heat for about 5 mins. I attempted to reinstall the new gaskets and found this more difficult than it needed to be. My solution was to simply remove both doors, remove all the screws and pull the door liners. Then I was able to easily install the gaskets, reinstall the liners and rehang the doors. As a result of pulling the inner liners was I discovered that 'Ice' had developed in the insulation (fiberglass) in the freezer door. I used a heat gun on low to melt the ice and then ran the insulation through the dryer to fully dry it before reinstallation. These added steps increased the total time for the repair but were well worth it in my opinion.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- cornelius from chicago, IL
- Parts Used:
- WPD7605115Q
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
27 y/o refrigerator whos' freezer &frige door gaskets are shot
The repair was done by removing the freezer door. I then remove all maybe 48 screws, lifted the inside panel and removed the the old worn gasket ,replacingit with the new making sure that it was seated properly around the panel. then I replaced all the screws and reinstalled the freezer door. Making sure contact is being made around the entire door, WALA,no more moisture, no more frost inside freezer or frige .AT THIS RATE I MIGHT HAVE THIS OLD FRIGE ANOTHER 27 YEARS.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Hawthorne, NJ
- Parts Used:
- WPD7605115Q
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
original freezer door gasket damaged
removed 30+ screws and interior freezer door panel in order to remove gasket. installed new gasket in reverse order as per instructions and payed attention to proper alignment of said gasket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Woods Cross, UT
- Parts Used:
- 12452602Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Broken wheel
Removed pin holding the wheel along with leveling screw. Put new wheel in place, replace pin and screw. Done...very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DONNA from AUBURN, PA
- Parts Used:
- D7605116Q, WPD7605115Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Moisture On Outside Of Refrigerator & Freezer. The Old Gasket Was Torn At Places.
Took the doors off,took inner plastic off and old gasket. Put new gasket on and put it back together. Used hair dryer to help shape it. It is working fine now. We saved hundreds of dollars doing it ourselves and not buying a new refrigerator!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Highland Mills, NY
- Parts Used:
- WPD7605115Q
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
gasket was not keeping freezer cold anymore
I didn't. first of all it was for my mother's refrigerator. She asked me to order the part. Her neighbor installed it for her. She said it took a while, but he was able to replace the gasket with the new one.
Was this instruction helpful to you?
Thank you for voting!