CSDI25E-L-P74100-8WL Amana Refrigerator - Instructions

Shut water off. Access rear area and removed water inlet line and leaving water and ice lines from old valve. Disconnected power wires from valve. Removed old valve and installed new valve. Reconnected all three water lines and checked for water leaks. Very easy

followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00

Replacement of the valve was pretty simple, after replacing the valve , ice maker still not making ice, after running the ice maker tests , using the test point, noticed the valve was working but no water to ice maker, the saddle valve was clogged, replaced saddle valve, now have lots of ice cubes. Also installed a water filter.

Pulled the fridge out, Took bottom panel off. Removed 3 screws holding motor. Unplugged connector, cut wires, attached old connector on new motor. put blade on new motor.installed in fridge, put cover back on.

pull unit away from the wall, and unplug it. remove the grill, and cardboard guard on the lower back of the unit. remove Three screws for the motor bracket. Remove the bracket legs from the old motor and assemble them to the new motor. take the fan blade off the old motor, place it on the new. Cut the wires at the old motor, strip the insulation back, use supplied wire nuts to connect the new motor. Reverse order to reassemble. Plug in unit to test function.

just as video instructions said, very easy just following them ,part arrived in very short time and was exact fit completely satisfied, saved repair man service charges and wait time

After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.

Mine was alittle different than the online instructions. 1. I removed the motor. 2. I took the fan off the old motor and cut the wires about 3" back from old motor. 3. Mounted the new fan on bracket and put the fan on the new motor. 4.connected wires that were cut and used wire nuts to connect. 5. Mounted bracket and motor/fan to unit and it works like its brand new. Thank you PartSelect!

I watched the video to get up the courage to try the repair myself. I figured out the refrigerator model umber and ordered the parts on line from Parts Select. Parts showed up in a few days. Pretty easy so far. Under close scrutiny of the wife, I unplugged the refrigerator. I used a nut driver on my cordless screw gun to remove the back cover and valve. I removed the plastic water lines and electrical connectors from the old valve and attached them to the new part. Everything matched perfectly. I replaced the valve and back cover. I pluged the refrigerator back in. It might have taken 20 minutes total. The wife has her icemaker back online and I'm a hero! Thanks Parts Select!

I knew the repair wasn't difficult. It was a matter of finding the replacement part. Luckily, I found the part via the internet on your site. Lucky for me, there was an installation video!! These videos are worth 1000 bucks!! Never have encountered a site with installation videos before. It gave me complete insight as to how the job was sequenced. I'm a very visual person, so videos are the perfect helper for me. With fewer and fewer affordable local service companies around to fix problems like mine, your site gave me the complete confidence to easily switch out the condensor fan. I completed the repair for about $63.00. Your site ROCKS! Keep up the repair videos because they are awesome and extremely helpful. I felt like your pricing was competitive for this item. Thanks again!!

opened box,read directions,took out bad motor,installed new one.PRESTO CHANGO way to go.

Replaced the intake water valve on the back side of the ref. The dual-valve water valve kit instructions were very good and the new replacement valve fixed the problem and the ice maker is working once again. The extra parts received were not needed as all the existing water lines connected without a problem to the new valve. It took a few hours for the Ref. and the ice maker to recycle and start to work properly. Pleasantly surprised that the parts were available for a 27 yr.old fridge.

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.

Easily removed the old solenoids and installed the new one, reconnecting water lines with no problems. Icemaker now working properly.

I found the condenser fan was not working so I bought a new condenser fan kit and installed it. Fixed!