ASD2522VRW01 Amana Refrigerator - Instructions

I just removed a few screews and took the cover out of the ice box. Put my voltage meter to the refrigeator and realized the the unit was not defrosting...I then got the part number and entered it in on your web site. A few days later my part arrived. I put the part on and in just about 20 minutes I was up an running again...Thank you Part Select for fast and great service. I own 35 rental properties and having a online appliance parts store really saves me a lot of time and money.

Thank you
Curtis Hall

tested thermostat and defrost time but both tested as working...called a repairman who came in and said they were both working...got annnoyed for not trusting myself. Repairman did say that he had seen defrost timers simply slow down, allwoing them to tesat as good but not actually working correctly. I ordered both the thermostat and the timer to cover all bases...actual replacement was simple.

Disconnect power to refrigerator. Removed all food from Freezer. Removed all Shelves and shelf clips. Used phillips screwdriver and removed 6 screws from lower rear panel covering evaporator coil. Removed panel. Pulled plastic fan blade off top of motor shaft. Unclip top front of black motor retainer clip which then allowed the rear clip to unhook. Removed clip. Then removed 3 wires from fan motor, noting proper location for replacement. Slide the fan motor out to the left. Installed new motor. Reinstalled clip, hooking rear side first. Then rehooked the 3 wires. Slide fan blade back on top until secure. Tested everything at this point before reassembling rear panel. Then replace rear panel, replace the 6 screws, replace shelf clips and shelves and replace food. Very easy to do and saved about $150 over a service call to troubleshoot and re-visit to install after getting part

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

First remove the ice container from the freezer
and dump all of the ice. Remove the four
screws holding the front ice container cover. Remove the control arm screw and bracket from the bottom of the ice container, remove crusher housing (screws and retainer clip). Remove nylon
bearing nut on front of auger shaft (left handed threads). Remove crusher blades and spacers (remember order of blades and spacers). Remove broken floating baffle. Replace baffle and reverse removal procedures.

The hardest part was getting the front cover plate off. I used two kitchen knifes one in each slot on the bottom of the plate and pried it off and unplug it. I removed one screw to release arm. I then used long nose pliers to remove the pin on door arm assemble. Then unplug door heater. New door has no heater. The heater had cooked the plastic arm, which caused the arm to fail. Then reassemble in reverse order.

removed the clip that the motor was attached too put the new motor back on reinstalled the clip back on the fridge plugged the wire harness in and works perfect now . it was easier to remove the clip than to try to install the motor by itself its just to tight and you cant get in there

Dog chewes up the original part. Got the replacement , put it on the filter turned to lock in place and tried tp pull out old filter ( same procedure has been done multiple times successfully) part broke instantly upon putting pressure tom pull out filter. Sent back to you the next day for replacement.

Linkage on the cold-control mechanism in the air diffuser assembly was broken. It was necessary to access the diffuser assembly from both the refrigerator and freezer sides of the unit.
Re-connected the linkage between the diffuser and cold-control assembly; remounted the two combined assemblies . . . refrigerator working nicely now.

Followed instructions supplied. It was relatively easy and the parts fit exactly right. Sears wanted twice as much for the part and service would have charged me another $100 to come to my home. I saved over $100 doing the project myself.

It was easy, I followed the instructions on the paper and it went well.

Removed face plate, disconnected wires, removed and replaced micro switch and control bracket.

I first removed the ice bin from freezer. There were four nut screws on back of ice bin cover that I removed with a screw driver, giving me access to the deflector. The deflector has two prongs that attach it securely to the ice bin, I used a phylips head screw driver to release the prongs from the deflector. I installed the new deflector by placing it through the bottom portion of deflector area, using the phyllips screw driver I engaged the prongs of the deflector into slots on ice bin. There was a hook on the back side of the deflector that went over a metal rod that controls the ice cube release. Then replace front cover of ice bin with the four nut screws and returned it to the ice maker location.

I replaced the control bracket, which has mounts for the switches used to activate the ice and water dispensers. The water switch mount was broken, so the switch would not activate. It was great that I could find this part (the control bracket) on PartSelect's site.

If the person doing the repair has a little patience, then he/she will be rewarded!:

The first step is to pry off the front panel: I pried off the panel at the bottom. It will pop off, but takes a little effort. I used a couple of screwdrivers to pull it up at a couple of spots at the same time. Once the bottom pops out, then I pulled straight up on the panel. (If you try to pop out the panel at the top, you will damage it, so make sure to pop it out at the bottom.)

Next, disconnect the wiring that goes to the panel, and put the panel aside.

I then took a digital picture of the arrangement of wires and switches on the control bracket.

I disconnected any wires going from the inner part of the refrigerator to the control bracket, and then unscrewed the control bracket.

After removing the old control bracket, I carefully noted how the two switches (one for ice, one for water) mount into it. I removed these switches and put them into the new control bracket.

I then remounted the control bracket into the refrigerator, screwing it into place. I used the digital picture that I had taken earlier to make sure that I knew how to reconnect all of the wires.

I plugged the the remaining wires to the front panel, and then snapped the front panel back into place on the refrigerator door.

I was done!

I first went on line to trouble shoot. Discovered it was the Ice Maker itself then then I entered the part number in your system to purchase the ice maker unit. When the unit arrived I simply took a socket for three bolts unplugged the electrical connection and reversed this for the installation. It was simple. I described to my secretary the process and she told her husband who in turn replaced their icemaker.