ASD2575BRW00 Amana Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Thomas from Va. Beach, VA
- Parts Used:
- W11342242
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
shut off arm broke
open ice maker door, use mirror to view slot in front of ice maker, slip piece in place and done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Richardson, TX
- Parts Used:
- 72017
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Scratches in Surface
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROGER from WAXHAW, NC
- Parts Used:
- WP2182179
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Worn out door plastic cam
Replaced the door cam on bottom of fridge door. ONE THING TO UNDERSTAND- THERE ARE 2 CAMS ON THE DOOR, LOWER AND UPPER, BUT THE UPPER CAM IS NOT LISTED ON THE "DOOR HARDWARE" DRAWING, ITS LISTED ON THE MAIN BODY DRAWING! BE SURE TO GET BOTH CAMS! (PARTSELECT COULD MAKE A NOTE THAT WHEN PEOPLE LOOK UP LOWER CAM, PUT A NOTE IN THERE SAYING Y0U NEED UPPER TOO!)So I had to order the upper cam later and install later. BUT it is quite easy to replace, unlike the video, I only needed 1 tool! The nut driver (electric screwdriver w nut driver head). Thanks -RF
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Doral, FL
- Parts Used:
- WPW10225581
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Refrigerator Wasn't Cooling,Evaporater Coil Freezing Up
I have a side by side so in order to access the bi-metal switch I first had to empty out the freezer. The switch is clipped on to the top of the evaporator coil. I had to remove 8 screws to remove the back panel of the freezer compartment. The bi-metal switch was right there in plain view. There are two colored wires that come out of the switch. I tried pulling them out of the socket they were plugged into but gave up for fear of breaking something. I ended up cutting the wires and splicing them together. I used the plastic twist caps. I made sure when I closed everything back up that the open end of the caps were pointing down so no water can accumulate in them. It has been 3 days now and so far so good
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Ringoes, NJ
- Parts Used:
- WPW10225581
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Auto Defrost Freezer keeps defrosting SIDE BY SIDE KITCHENAID
DISCONNECT POWER. Removed all shelves/baskets.Popped upper panel off (just clips in) Removed 6 screws in lower back panel ( 3 each side) slid panel in place but down. You can then easily see the defrost thermostat/defrost termination switch. Cut the wire connectors (pink n brown wire) stripped back wire, attached new defrost thermostat. Thermostat clips on. New thermostat ohm's at 5.5, old one was "open". Slid cover back up meeting the upper cover grooves. Screwed lower panel in. Put shelves etc back in. Plugged in. Turns on, put a bottle of water in freezer. Checked a while later, frozen. has been frozen for a week.
-James
-James
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from Albuquerque, NM
- Parts Used:
- WP2187172
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The bin broke
I took out the broken bin and put in the new one. This is about the 5th bin I've had to replace. That maxed out my repair abilities.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Belleville, WI
- Parts Used:
- WP2198202
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Our six year old fridge would not stop running - everything was frozen. Found if I tapped on the Tstat I could sometimes get it to turn off.
Remove the knobs and faceplate to get at the screws behind it. Removing the sensor is a bit involved but everything else is fairly straight forward. See other postings for description / order of operation. Replacement took less than 30 minutes.
Works great now!
Works great now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from Twin Peaks, CA
- Parts Used:
- WP2187172
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Door Shelves
I ordered the parts, three days later they were in my hands, and installed in the door of the refrigerator. Total time, two minutes! Perfect fit. Ordering the parts was the easiest thing I have ever done. This site is the best! Thank You!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from NORTH PORT, FL
- Parts Used:
- WP2152713
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Ice maker would only deliver crushed ice not cube's
Switched Electric breaker to off. Removed all food and ice cube tray from freezer. Remove 4 screws on soleniod cover in rear of freezer. Removed two screws, two elec connectors from old soleniod and removed. Installed new soleniod. Reinstalled elec connectors and screws, ice cube tray and food. Turned breaker on . Ice maker worked properly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leo from Salem, SC
- Parts Used:
- WP2300868
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Had to replace a hose connector at the base of my refrig/frreezer
Perhaps a helpful hint:
When aI received the hose adapter/connector, I inserted the 2 hose ends only to have water drip from the connection.
I used a utility knife to remove an inch from each side, then reinserted the hoses. That made the differnce. Dry as a bone.
LG
When aI received the hose adapter/connector, I inserted the 2 hose ends only to have water drip from the connection.
I used a utility knife to remove an inch from each side, then reinserted the hoses. That made the differnce. Dry as a bone.
LG
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Leesburg, FL
- Parts Used:
- W10508993
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Shelf Bracket
Removed food itmes on broken shelf. Removed old glass shelf cover. Removed broken shelf bracket. Installed new shelf bracket. Intalled new glass shelf cover. Replaced food items back on shelf
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- douglas g. from roanoke, VA
- Parts Used:
- WP2188664
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken meat and vegatable draw
a simple replacement
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HAROLD from SPRING HOPE, NC
- Parts Used:
- WPW10169511
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
motor coupling weld broken
Removed four screws from ice maker motor/light support.Then unplugged electrical plug from side of freezer.Used two slip joint pliers to remove coupler from motor shaft. installed new coupler to shaft hand tight as will tighten as motor is run.Then reversed tear down order.
Ice dispenser works better than when we first got the refrigerator
Ice dispenser works better than when we first got the refrigerator
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Westlake, OH
- Parts Used:
- WP2198202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
refrigerator was intermittently cooling because thermostat contacts burned away.
Turn off the fridge and unplug the power. Inside the refrigerator unit, remove two plastic panels extending from the front to the rear cooling vent by unscrewing two screws. Gently unhook the thermostat tube from the rear vent.
On the control panel, gently pry off the two control knobs and the front control panel. Remove four screws to drop down the control assembly. Unplug the left electrical connector and unscrew the lever control arm being careful not to bend it. Disconnect the right side electrical connector and you can now remove the control unit to a table to easily work on it.
Undo two screws to remove the thermostat bracket. Undo two more screws to remove the thermostat assembly. Install the new thermostat and reverse the process just described. It takes about 15 minutes if you know what to do ahead of time. You will have to reuse the plastic tube that covers the thermostat sensing tube.
On the control panel, gently pry off the two control knobs and the front control panel. Remove four screws to drop down the control assembly. Unplug the left electrical connector and unscrew the lever control arm being careful not to bend it. Disconnect the right side electrical connector and you can now remove the control unit to a table to easily work on it.
Undo two screws to remove the thermostat bracket. Undo two more screws to remove the thermostat assembly. Install the new thermostat and reverse the process just described. It takes about 15 minutes if you know what to do ahead of time. You will have to reuse the plastic tube that covers the thermostat sensing tube.
Was this instruction helpful to you?
Thank you for voting!
Refrigerator door failing to close without being pushed shut
Replaced upper cam piece on bottom hinge and also replaced pivot thimble on upper hinge.
No problems, except pivot thimble glued in place. Had to cut up and pull out with pliers. Everything works like new now.
No problems, except pivot thimble glued in place. Had to cut up and pull out with pliers. Everything works like new now.
Was this instruction helpful to you?
Thank you for voting!